How to find Current and Voltage using impedance? Please do not round.
I'm having trouble reducing the circuits into the correct form to solve for the asked values.
How to find Current and Voltage using impedance? Please do not round. I'm having trouble reducing...
Review Part A. Find the relationship between the phasor voltage and phasor current for a resistance The resistor shown here has been transformed into the phasor domain: Ik 4k Suppose that the phasor current is given by IR = 752120 mA. Find the phasor voltage VR. Enter a complex number in polar form, with phase angle in degrees. View Available Hint(s) 3002120 V Submit Previous Answers Correct Part B - Draw the phasor diagram of the resistance from Part A...
2) For the circuit shown, draw the phasor equivalent circuit for the described circuit, and answer the questions below. then find the voltage across the current source (v(t)). Note for questions b and c you need to determine the instantaneous power associated with the source using values for P and Q(P and Q are determined from the phasor analysis results for V and Ig) and then use the trig identity Acos(x)Bsin(x) = V42 + B2 cos(x-Tan(B/A to convert Pcos(x) -...
In the adjoining circuit schematic, in steady-state, the current flowing through the loop causes a voltage drop across the resistor, having the waveform vR(t) = 15 cos (75 t) and a voltage drop across the capacitor given by vC(t) = 20 cos (75 t + 90⁰) (a) Express the above two voltages in phasor form. (b) Find the source voltage shown in the circuit schematic, expressed in phasor form. (c) Express the source voltage v(t) as a function of time....
Can Someone explain how to do this problem? 4. Current and Voltage Source with Diode: For the circuit shown below, find the voltage vo. The current-voltage relationship for the diode is, as usual, Io(e"s/V 1) where Io 10-12 A and VT 0.026 V 10Ω 10 V (+ 5 mH Uo 1 A 4. Current and Voltage Source with Diode: For the circuit shown below, find the voltage vo. The current-voltage relationship for the diode is, as usual, Io(e"s/V 1) where...
can someone please explain how to solve this problem? thanks 4. Current and Voltage Source with Diode: For the circuit shown below, find the voltage vo. The current-voltage relationship for the diode is, as usual, I = VT = 0.026 V. Io (e/Vr 1 where Io = 10-12 A and + vf 10 15 + 10 V (+ 1 A Vo 5 mH 4. Current and Voltage Source with Diode: For the circuit shown below, find the voltage vo. The...
Please do all parts and show work, thank you! 7. 3 mH Determine the equivalent impedance, Zeq, of the circuit. Write your answer in rectangular form. (3 pes) 4cos(1000+459 v O s 5: 1 mF Zaorson 22: jwej (COX 3)-33 zce (1000/12.3. Zoo Za + ZL + Zc Sch+j3 cm + -j Zeq = 5 + je on I mi 8. Solve for v.(t). Write your answer in the time domain. (6 pts) 312 102 cos(10') v Y () 1012...
1. RL Circuits For the circuit in Figure 1, find the inductor voltage vit) if a) v(t) is the step function: 0 Vfor t<0 and 10 V for t>0. What is the time constant in this case? b) vs(t) 15 cos(100 t). You may use either the direct time-domain method, or use (complex) phasor method. 52 102 5mH L(t) Figure 1 2. Impedance You are given six black boxes, labelled "1" to ", each with two terminals. You are told...
can you solve this 5 problem please Q2. Using voltage divider and/or current divider to find the unknown on each of the circuits: 40 V -) ) ξR, υ ξR, 6 Ω 20 Ωξυ, 2.4A 1) 1890 Ω ξ10Ω 10 Ω ξ5 kΩ 360 kΩ 45 VI + υ, ξ 20 kΩ ξ90 ΚΩ Q3. Using a Y to delta transformation find the currents il, i2, and i3. And the power delivered by the source. 56 Ω 44Ω 80 Ω...
ANSWER ALL PLEASE Question 43 2 pts The rms voltage across and the rms current through a single circuit element connected to an ac generator are, respectively, Vrms = 131 volts and Ims = 37 A. The angular frequency of the generator id w = 78. It is observed that the current leads the voltage by 90°. The element that is connected to the ac generator is either a capacitor, an inductor, or a resistor (only one of the three)....
can you show how the model would look like on matlab ? please help with this question For the circuit given below, find the normal form for the inductor current and capacitor voltage. Use Matlab (Create an.m file. Use Isim function) and Simulink (Create a Simulink Model). Plot the responses x1 and x2 over time from the M file and Simulink Model. Do they match? Please explain. Use f(t)-e-cos(2t)u(t) for the input. Assume Zero Initial Conditions. 2Ω I H On...