Which of the following will produce zero torque? List all that apply.
a) having a lever arm of zero length.
b) applying zero force.
c) having an angle between the applied force and the lever arm of zero degrees.
Which of the following will produce zero torque? List all that apply. a) having a lever...
1. What is the linear (translational) analog for torque? A. Mass B. Acceleration C. Velocity D. Force 2. What is the linear (translational) analog for the 'moment of inertia'? A. Velocity B. Mass C. Force D. Acceleration 3. The torque on a lever arm is maximized when the force is forming what angle with the lever arm? A. 45 degrees B. 90 degrees, or perpendicular to the lever C. 60 degrees D. 0 degrees or parallel to (alongside) the lever
If I am applying a torque to a wrench such that the angle between the force applied and the wrench is 30 degrees, how much more torque could I apply if I was pushing with the same amount of force but at 90 degrees to the wrench?
A torque RF is applied on a door by pushing with a perpendicular force F at a distance R from the hinge (axis of rotation), which of the following will increase the magnitude of the torque? Mark all that apply. a. Move force F closer to the axis of rotation. b. Move force F farther from the axis of rotation. c. Apply force F parallel to the moment arm. d. Apply force F at an angle of 30 to the...
In each of the diagrams below, O refers to the pivot point and P is the point of application of the force. In all cases the magnitude of the force is the same and the distance between O and P are equal 0 0 0 0 0 (a) In which one af the diagrams does the line of action of the force pass through the pivot point? (Select all that apply) a diagram (i) a diagram (ii) a diagram (iii)...
please answer all parts to each question P1300 35° Length 797 d1 pivot d2 Length Art of rotation Axs of row Arir of 30 50 115 pivote 156 Length Length L lal (f) (e) The purpose of this problem is for you to practice: (1) the steps making drawings of lever arm, (ii) applying the proper trignometrical functions to calculate the lever arm. For each figure, do the above mentioned practice. a) In Figure (a) the distance from the pivot...
What factors determine the torque generated by a force? Select ALL factors. distance between where force is applied and the axis of rotation whether the force is conservative or non-conservative. magnitude of the force orientation of the force. A force F is applied at the position shown where is the vector from the axis of rotation to where the force is applied. The notation on the diagram is: r=|| F ||and F =|| F | F and F. - components...
I've been having some trouble figuring out where to start on this maths task: Investigate how the gears of a multi-speed bicycle allow a rider to increase torque with reduced effort: You will need to obtain relevant measurements, such as the length of the moment arm for each of the gears. You may use research or collect your own measurements. Consider your assumptions, which should be reasonable (eg, pedal force applied by the rider). Simulate the relationship...
need help with the FBD, the unknowns, and L1 and L2 thank you In this case both top and bottom supports of the PVC pipe are fixed. There is only one lever arm at the center of the pipe where torque is caused by applying weights of 5 N on each side of the hanger. Place dial gage at the point where load is applied to measure the deflection caused by it. After making the initial reading zero on the...
QUESTION 1 What is the net torque in a rotational equilibrium? Sum of all forces undefined Depends on different factors. zero QUESTION 2 A force of 500 N is applied to the free end of a beam attached to a wall. The length of beam is 5 m. The force is applied at an angle of 300 to the beam. What is the amount of torque applied at the fixed end of the beam? 1250 N m 1300 N m...
Exploration 2.2 For this Exploration, find a door at home. First apply a force perpendicular to a line through the pivot point (the door hinge) and the point of application. In other words, apply a force perpendicular to the door. Depending on the mass of the door, the force applied may not need to be very large. Just make sure you use the same force for all portions of this exercise. Then apply the force at an angle. Is the...