Homework Answers
Add Answer to:
Please solve mechanics of materials
MECE201 Lectures.. x 26 26 If the C-clamp shown in the...
Determine the maximum ram force P that can be applied to the clamp at D if...
Determine the maximum ram force P that can be applied to the clamp at D if the allowable normal stress in the clamp is 180 MPa for both tension and compression. The clamp has a T-shape cross section shown through a-a. Ans: 9.08 kN
2. The C-clamp applies a compressive force of 40 lb on the cylindrical block. Determine the...
2. The C-clamp applies a compressive force of 40 lb on the cylindrical block. Determine the maximum normal stress developed in the clamp. Sketch the stress distribution at the (clamp) section. (20 points) in. 0.25 in. 4 in. 4.5 in. 0.75 in.
Mechanics of materials a) Determine the maximum shear stress on the axis that works with the torsional moments as shown...
Mechanics of materials
a) Determine the maximum shear stress on the axis that works with
the torsional moments as shown in the figure
b) Find the angle of torsion in degrees between the two ends has
that G = 8.4 ^ 5 Kgf / cm2
Outside diameter: 50mm
Inner diameter: 30mm
Sorry :')
mM
mM
2) [30 pts] C-clamp with handle, power screw For the C clamp shown, a force is...
2) [30 pts] C-clamp with handle, power screw For the C clamp shown, a force is applied at the end of the 0.375 in diameter handle. The screw is a 0.75 in-6 Acme thread (from Figure 8-3), and is 10.4 in long overall, with a maximum of 8 in possible in the clamping region. The handle and screw are both made from cold-drawn AISI 1006 steel. The coefficients of friction for the screw and the collar are 0.15. The collar,...
A compressive force of 450 N is to be applied to the two boards in the grip of the C clamp shown ...
A compressive force of 450 N is to be applied to the two boards in the grip of the C clamp shown in Figure 13. The threaded screw has a mean diameter of 12 mm and advances 2.8 mm per turn. The coefficient of static friction is 0.20. Neglecting any friction at point A Determine the force F which must be applied to the handle at C in order to i. Tighten the clamp to provide the clamping force. ii....
Mechanics of materials question HW 9 Problem 9.16 Part A Determine the equivalent state of stress...
Mechanics of materials question
HW 9 Problem 9.16 Part A Determine the equivalent state of stress on an element at the point which represents the principal stresses and the maximum in-plane shear stress and the associated average normal stress. Also, for each case, determine the corresponding orientation of the element with respect to the element shown in the figure below. Suppose that Determine the orientation of principal planes of stress Express your answers using three significant figures separated by a...
Please help me to solve this quiestion Mechanics of material The column AB shown in the...
Please help me to solve this quiestion
Mechanics of material
The column AB shown in the Figure below is made of A-36 steel, which is fixed at A and pinned at B. The column has a circular hollow section as shown in section a-a, which has an outer radius ro= 25mm and inner radius ri=20mm. (a) Determine the slenderness ratio of the column [5%] (b) Is the column safe? [12%) (c) What is the failure mode of the column [3%)...
20:01 V.VB/s STC Exam-2.pdf Subject: Mechanics of Materials Code: CE 202 Semester 411 QUESTION #2 Beam...
20:01 V.VB/s STC Exam-2.pdf Subject: Mechanics of Materials Code: CE 202 Semester 411 QUESTION #2 Beam AE is loaded as shown in the Figure. a) Draw the shear force and the bending moment diagrams for the beam. Clearly mark the numerical values at points A, B, C, D and E. b) What are the maximum bending moment and the maximum shear force? State where they occur 4 kN/m 5kN com Tosmosm/10m Student Name:................... ................... ...... Student ID...... Page 3 of...
Philpot, Mechanics of Materials, 3e Mechanics of Materials (CENE 253 STANDARD VIEW PRINTER VERSION BACK NEXT...
Philpot, Mechanics of Materials, 3e Mechanics of Materials (CENE 253 STANDARD VIEW PRINTER VERSION BACK NEXT P9.026 The ctever beam is sublected to a concentrated load of P - 46 kips. The cross-sectional dimensions of the wide-flange shape are shown in the second figure. (a) the shear stress T- at point H, which is located 3.1 in. below the centroid of the wide-flange shape. x Not Correct Assume yw-3.1 in., -1.9 in., d-10.1 in., t 0.261 in., tr-0.321 in., br...
solve 1 and 3 please Wut unte. 02/06/2020, 12:00pm) Problem 1 (50 pts): For the beam...
solve 1 and 3 please
Wut unte. 02/06/2020, 12:00pm) Problem 1 (50 pts): For the beam shown, a) Determine the reaction forces at the supports b) Derive the loading, shear-force, and bending moment relationships (g(x), and c) Draw the V(x) and M(x) graphs and identify the locations of the maximum shear force and bending moment along the beam d) Determine the maximum tensile and compressive stresses e) Determine the maximum shear stress due to V 13 kN 50 mm --...
Determine the maximum ram force P that can be applied to the clamp at D if the allowable normal stress in the clamp is 180 MPa for both tension and compression. The clamp has a T-shape cross section shown through a-a. Ans: 9.08 kN
2. The C-clamp applies a compressive force of 40 lb on the cylindrical block. Determine the maximum normal stress developed in the clamp. Sketch the stress distribution at the (clamp) section. (20 points) in. 0.25 in. 4 in. 4.5 in. 0.75 in.
Mechanics of materials
a) Determine the maximum shear stress on the axis that works with
the torsional moments as shown in the figure
b) Find the angle of torsion in degrees between the two ends has
that G = 8.4 ^ 5 Kgf / cm2
Outside diameter: 50mm
Inner diameter: 30mm
Sorry :')
mM
mM
2) [30 pts] C-clamp with handle, power screw For the C clamp shown, a force is applied at the end of the 0.375 in diameter handle. The screw is a 0.75 in-6 Acme thread (from Figure 8-3), and is 10.4 in long overall, with a maximum of 8 in possible in the clamping region. The handle and screw are both made from cold-drawn AISI 1006 steel. The coefficients of friction for the screw and the collar are 0.15. The collar,...
A compressive force of 450 N is to be applied to the two boards in the grip of the C clamp shown in Figure 13. The threaded screw has a mean diameter of 12 mm and advances 2.8 mm per turn. The coefficient of static friction is 0.20. Neglecting any friction at point A Determine the force F which must be applied to the handle at C in order to i. Tighten the clamp to provide the clamping force. ii....
Mechanics of materials question
HW 9 Problem 9.16 Part A Determine the equivalent state of stress on an element at the point which represents the principal stresses and the maximum in-plane shear stress and the associated average normal stress. Also, for each case, determine the corresponding orientation of the element with respect to the element shown in the figure below. Suppose that Determine the orientation of principal planes of stress Express your answers using three significant figures separated by a...
Please help me to solve this quiestion
Mechanics of material
The column AB shown in the Figure below is made of A-36 steel, which is fixed at A and pinned at B. The column has a circular hollow section as shown in section a-a, which has an outer radius ro= 25mm and inner radius ri=20mm. (a) Determine the slenderness ratio of the column [5%] (b) Is the column safe? [12%) (c) What is the failure mode of the column [3%)...
20:01 V.VB/s STC Exam-2.pdf Subject: Mechanics of Materials Code: CE 202 Semester 411 QUESTION #2 Beam AE is loaded as shown in the Figure. a) Draw the shear force and the bending moment diagrams for the beam. Clearly mark the numerical values at points A, B, C, D and E. b) What are the maximum bending moment and the maximum shear force? State where they occur 4 kN/m 5kN com Tosmosm/10m Student Name:................... ................... ...... Student ID...... Page 3 of...
Philpot, Mechanics of Materials, 3e Mechanics of Materials (CENE 253 STANDARD VIEW PRINTER VERSION BACK NEXT P9.026 The ctever beam is sublected to a concentrated load of P - 46 kips. The cross-sectional dimensions of the wide-flange shape are shown in the second figure. (a) the shear stress T- at point H, which is located 3.1 in. below the centroid of the wide-flange shape. x Not Correct Assume yw-3.1 in., -1.9 in., d-10.1 in., t 0.261 in., tr-0.321 in., br...
solve 1 and 3 please
Wut unte. 02/06/2020, 12:00pm) Problem 1 (50 pts): For the beam shown, a) Determine the reaction forces at the supports b) Derive the loading, shear-force, and bending moment relationships (g(x), and c) Draw the V(x) and M(x) graphs and identify the locations of the maximum shear force and bending moment along the beam d) Determine the maximum tensile and compressive stresses e) Determine the maximum shear stress due to V 13 kN 50 mm --...
Most questions answered within 3 hours.
-
In a competitive inhibition, Km is increased while Vmax is
unchanged. An enzyme is being assayed...
asked 25 minutes ago -
Applied manufacturing overheads are overheads allocated to the
production process according to a tariff, based on...
asked 23 minutes ago -
you are required to develop a simple HR application for a small
accounting firm that wishes...
asked 22 minutes ago -
The following present value factors are provided for use in this
problem.
Periods
Present Value
of...
asked 27 minutes ago -
Celine beauty is a new cosmetics manufacturer that produces
skincare box and makeup box. Demand over...
asked 34 minutes ago -
Eleanor and Kyoko are roommates. They spend most of their time
studying (of course), but they...
asked 41 minutes ago -
Answer the questions
1.What is the value of a stock based on the dividend-growth
model if...
asked 42 minutes ago -
Per the Barron's report the average weeks unemployed is 21.5
(population mean) with a population standard...
asked 1 hour ago -
1.. All following elements have been identified as
important to supporting school’s level of involvement with...
asked 44 minutes ago -
A hypothesis test is used to test the hypotheses H0:
μ = 10.5 versus HA: μ...
asked 1 hour ago -
8.41- From a list of the 729 people who went on a cruise, 25
were randomly...
asked 1 hour ago -
A derrick boat approaches a two-mile marker 100 m ahead at a
velocity of 29.0 m/s....
asked 57 minutes ago