Note-please find me in comment box if you find any difficulty. Please note that as which model is to be used not given, I use h parameter. As we have different models for analysis, answer may vary with other model. Good luck
Compute the voltage gain, input and output impedance for the following circuit if ß = 150...
(b) Compute the voltage gain, input and output impedance for the following circuit if ß = 150 and VBEQ = 0.7 V, V1 = 26 mV. A + 10 V 40 ΚΩ R1 4 ΚΩ Ci CO Vs R2 VO 60 ΚΩ 5 ΚΩ RE RL 1ΚΩ
Q. 4. (a) Draw a small signal equivalent circuit by replacing the BJT with its hybrid-mt model for the circuit shown below. Also derive an expression for Zin when la is neglected. (10) + Vx (b) Compute the voltage gain, input and output impedance for the following circuit if ß = 150 and VBEQ = 0.7 V, V1 = 26 mV. (15) A+ 10 V 40 ΚΩ R1 4 ΚΩ Сі CO Vs R2 vo 60 ΚΩ 5 ΚΩ RE...
The input impedance Zi, the output impedance ZO and the voltage gain AV = (VO / Vi) of the two- stage amplifier circuit in the figure Calculate the values. According to these values you find, when an input voltage is applied to the circuit as shown in the figure What is the maximum value Vomax and shape of the exit sign? Show approximate on a chart +15V 3.3k22 47kQ2 2.4 ΚΩ 0.5uF HE D B Ho 0.5 UF Ipss =...
3. In the amplifier circuit given below; Zi input impedance and circuit from input to output Calculate the total voltage gain [AV=(Vo/Vi)] which is. S-3) (20 Puan) Aşağıda verilen yükselteç devresinde; Zi giriş empedansını ve devrenin girişten çıkışa V olan toplam gerilim kazancını 4, = hesaplayınız. V +10 V R 10K R 10KOS Q Si B=100 R4 1ΚΩ Q6 Si B=100 r=o0 Vi R 15ΚΩ Si B=100 N Q3 Si B=100 RS 1202 Si B=100 Q5 Si B=100 3,6ΚΩΣ RE...
BJT and Amplifier Circuits +15 V 27 k R2 680 Ω Compute: 53 1. Show the extra units and connections RE 680 2 R2 12 kC2 2. The input and the output impedance 3. The Voltage gain Av 4. If the input ac voltage with Vp-1 mV, draw the output voltage. What is the maximum vin value. 5. 6. The current gain Ai and Ap. 7. Compute the produced power and the consumed power in transistor and RL. BJT and...
Please answer clearly Question 2 The amplifier shown in Figure 2 has the following parameters: Kn(W/L)-1 mA/V2, V-1 V Determine a) Voltage gain (Vo/vi) b) Input resistance (R) c) Output resistance (Ro) d) Maximum output voltage swing so as the amplifier stays in saturation mode. Assume VDD-20 V, R1-2.5 ΚΩ, R2-1KQ, R3-0.5 ΚΩ, R4-5 MQ, R5_1ΜΩ. R4 R1 R5 R2 Ro R3 Question 2 The amplifier shown in Figure 2 has the following parameters: Kn(W/L)-1 mA/V2, V-1 V Determine a)...
What are the Input impedance, output impedance, voltage gain and current gain equations for a common emitter amplifier biased using emitter bias? (Plus please provide the circuit)
For the circuit below, the output is at 15 V and the input voltage is at +2 V if the input voltage is gradually lowered to -2 V, at what input voltage does the output switch from +15 V to-15 V (to 1 % accuracy)? The op-amp has rail-to-rail swing, and a gain-bandwidth product of 3 MHz. The resistors used are r1 -1.5 k ohm and r2 22.8 k ohm r2 Vin 2 +2 V +15 V r1 f 1...
The circuit 3-The circuit of problem # 2 is subjected to a small ac input by the signal generator. By neglecting the voltage drop across the coupling and bypass capacitors, determine the small signal voltage gain Vo/ Vì = Avi , input resistance Ri-vi / ii and the output resistance Ro external to R Avi= Ri= , Ro The accompanying circuit shows a 4-resistor biased JFET transistor Determine the values of Rp and Rs so that the Q-point is equal...
The circuit below is a common collector (CC) circuit. Assuming VBEON VA, and ß - 100, , VCE.SAT 0.2V, VA 00 Calculate the transistor operating point. a. 1 b. Find the small signal voltage gain, 。 Find the driving point input resistance. c. d. If the input is a sinewave, find the maximum output voltage amplitude before clıpping sets in. B1 CO Q1 RE v,RB2 Assuming VBEON VA, and ß - 100, , VCE.SAT 0.2V, VA 00 Calculate the transistor...