AC generators (often called alternators) used in airplanes and submarines are quite common having a frequency...

Question

Question

AC generators (often called alternators) used in airplanes and submarines are quite common having a frequency of 400 Hz and a

engineering Electrical-Engineering

Add a comment Improve this question Transcribed image text

Answer 1

Answer #1

Given data, Vi = 24 cms) 400N 2 с 4000UF R 2:40 solution: Vac 2. Vmax 0.637 Vmax -0.9 Vrms T -0.9 X24 21.6 V. i I Idc Vac R 2

Add a comment

Answer 2

Similar Homework Help Questions

AC generators (often called alternators) used in airplanes and submarines are quite common having a frequency...

AC generators (often called alternators) used in airplanes and submarines are quite common having a frequency of 400 HZ and an output voltage of 24 volts (rms). If one of these generators is connected to a diode bridge rectifier with a 4000-μF capacitor. (a) Calculate the load current when a resistive load of 2.4 Ω is connected. (b) Calculate the AC ripple voltage across the above load. (c) Calculate the average current passing through the diodes. (d) Calculate the minimum...
1. AC generators used in submarines quite often have a frequency of 1,000 Hz and an...

1. AC generators used in submarines quite often have a frequency of 1,000 Hz and an output voltage of 24 volts (r m s ). If this generator is connected to a diode bridge rectifier: (a) Hat I sthe output DC average voltage without a filter capacitor? (b) With capacitors of 10,000 micro farads, but no load, what is the output Vdc capacitor as a filter as, but no load, what is the output VDC? (c) When a resistive load...
1. Power supply (ac to dc) design. [10 pts.] Design a full-wave bridge rectifier circuit to deliv...

1. Power supply (ac to dc) design. [10 pts.] Design a full-wave bridge rectifier circuit to deliver 10 volts dc with less than 0.1 volt (peak to peak) ripple into a load drawing up to 10 mA. (a) Choose the appropriate ac input voltage from the transformer secondary assuming the usual voltage drops for silicon diodes. (b) Determine the correct capacitor value to ensure the specified ripple in your calculation (c) What fuse value should you select for the primary...

3. When diodes that have unequal junction capacitances are connected in series in a circuit, they'll often be protec...

3. When diodes that have unequal junction capacitances are connected in series in a circuit, they'll often be protected by A. parallel diodes. B. parallel capacitors. C. series resistors. D. parallel resistors. 5. The front-to-back resistance ratio of a power supply rectifier diode must be no less than A. 30 to 1. B. 2 to 1. C. 5 to 1. D. 10 to 1. 15. Which of the following is the correct equation for the percent regulation of a power...
Q4. Most electronic systems need a dc voltage to work properly. The AC-to-DC power supply system ...

part g Q4. Most electronic systems need a dc voltage to work properly. The AC-to-DC power supply system is including a transformer, a rectifier and a capacitor input filter. The AC input voltage is 110 Vrms at 60 Hz. (a) Draw the full wave bridge rectifier circuit with transformer which steps down voltage to safer and lower levels that are more suitable for use with diodes (b) Show how the capacitor input filter connects to the rectifier output in the...
A full-wave diode rectifier supplies a 30Ω resistive load from a 400Hz, 110V single-phase AC supply....

A full-wave diode rectifier supplies a 30Ω resistive load from a 400Hz, 110V single-phase AC supply. A capacitor is connected in parallel with the load. Calculate the capacitance required if the maximum peak-to-peak voltage ripple across the resistor is to be restricted to 10V. You may assume that the RC product of the resistance and capacitance will be significantly greater than the period of the AC waveform. State any other assumptions made.

Even just steps/formula on what to follow would be sufficient if you cannot complete the question.

Even just steps/formula on what to follow would be sufficient if you cannot complete the question. Draw a bridge rectifier fed from a single-phase 240-V (Au) supply with a 4:1 step down transformer. A 10-2 load is connected to the output. Assume a simplified model for the diodes with VoN 1V per diode and zero leakage current. (a) Draw voltage, current and p(t) waveforms for one diode. (b) Derive the diode voltage spec from the voltage waveforms, and add 50%...
VOLTAGE-DIVIDER BIAS 179 CONFIGURATION h determined in Example 4.7. Essentially, exact and approx...

VOLTAGE-DIVIDER BIAS 179 CONFIGURATION h determined in Example 4.7. Essentially, exact and approximate techniques is the ten the 07 step down transformer and a load RL of 820 ohms. It is connected to an ac source of 100 VAC rms, 50 Hz. (hint: note the rms values, and for diode PIV, assume ideal diodes and draw the PIV eqv ckts) ve rectifier circuit has a 10:1 3. A positive output, a. Draw this circuit.. b. Find Vp and Vave at...
Design a FULL WAVE BRIDGE RECTIFIER circuit that will: Take 120volts ac, 60 hz, sinusoidal waveform...

Design a FULL WAVE BRIDGE RECTIFIER circuit that will: Take 120volts ac, 60 hz, sinusoidal waveform and convert it to a “regulated “dc value giving 12 volts +, - 1 volt across a 2000-ohm output load resistor with no more than 2% ripple voltage. You may assume: a. An ideal power transformer as discussed in class. b. For hand computations, you must assume a diode given by Figure 4.8 page 185. c. A filter capacitor sized per the textbook equation...

A DC and AC voltmeter are used to measure the output voltage of...

A DC and AC voltmeter are used to measure the output voltage of a filter circuit connected to full wave rectifier circuit operating at 60Hz, supplying load of 5hp DC Motor (1hp=0.75kW). The readings of the two voltmeters are 250V and 2.0V respectively. Calculate a) The ripple factor of the filter. b) The value of filter capacitor.

AC generators (often called alternators) used in airplanes and submarines are quite common having a frequency...

Homework Answers