1. AC generators used in submarines quite often have a frequency of 1,000 Hz and an output voltage of 24 volts (r m s ). If this generator is connected to a diode bridge rectifier:
(a) Hat I sthe output DC average voltage without a filter capacitor?
(b) With capacitors of 10,000 micro farads, but no load, what is the output Vdc capacitor as a filter as, but no load, what is the output VDC?
(c) When a resistive load is connected to he rectifier with the above capacitor, the output DC voltage becomes 28 V. What is the resistance of the load? What is the current?
1. AC generators used in submarines quite often have a frequency of 1,000 Hz and an...
AC generators (often called alternators) used in airplanes and submarines are quite common having a frequency of 400 HZ and an output voltage of 24 volts (rms). If one of these generators is connected to a diode bridge rectifier with a 4000-μF capacitor. (a) Calculate the load current when a resistive load of 2.4 Ω is connected. (b) Calculate the AC ripple voltage across the above load. (c) Calculate the average current passing through the diodes. (d) Calculate the minimum...
AC generators (often called alternators) used in airplanes and submarines are quite common having a frequency of 400 Hz and an output voltage of 24 volts (rms). If one of these generators is connected to a diode bridge rectifier with a 4000-uF capacitor. (a) Calculate the load current when a resistive load of 2.4 12 is connected. (10 points) (b) Calculate the AC ripple voltage across the above load. (10 points) (c) Calculate the average current passing through the diodes....
part g Q4. Most electronic systems need a dc voltage to work properly. The AC-to-DC power supply system is including a transformer, a rectifier and a capacitor input filter. The AC input voltage is 110 Vrms at 60 Hz. (a) Draw the full wave bridge rectifier circuit with transformer which steps down voltage to safer and lower levels that are more suitable for use with diodes (b) Show how the capacitor input filter connects to the rectifier output in the...
A DC and AC voltmeter are used to measure the output voltage of a filter circuit connected to full wave rectifier circuit operating at 60Hz, supplying load of 5hp DC Motor (1hp=0.75kW). The readings of the two voltmeters are 250V and 2.0V respectively. Calculate a) The ripple factor of the filter. b) The value of filter capacitor.
1) What component in a power supply converts ac line voltage to dc voltage? a. Transformer b. rectifier diode c. resistor d. capacitor 2) A circuit that provides an entirely positive or negative output voltage when an ac input voltage is applied is called a a. rectifier b. inverter c. filter capacitor d. zener diode 3) A control voltage or current is the a. power factor b. bias c. ground d. load 4) When the voltage at the op amp's...
1. A single-phase, full wave rectifier has an AC source with Vm=24 volts at f=60 Hz. Determine the 2th harmonic of the output voltage. 2. The average current of a single phase bridge rectifier at its DC side is 6.94 amps. What is the average current flowing through each diode?
Design a FULL WAVE BRIDGE RECTIFIER circuit that will: Take 120volts ac, 60 hz, sinusoidal waveform and convert it to a “regulated “dc value giving 12 volts +, - 1 volt across a 2000-ohm output load resistor with no more than 2% ripple voltage. You may assume: a. An ideal power transformer as discussed in class. b. For hand computations, you must assume a diode given by Figure 4.8 page 185. c. A filter capacitor sized per the textbook equation...
please help Question 1 Consider the following circuit, where the reverse saturation current (Is) is the same for each diode. D2 o Vo Di Vi WWW R 32 23 a. b. Determine an algebraic expression for V1, for a given Vo, and Is. Given an Is of 40 FA and R1 = 3.3 kl , determine the Vi that produces an output voltage (V.) of 0.625 V. C. Recalculate question-b if Is were to be a thousand times greater at...
Capacitor is connected to secondary (1) A fullwave bridge rectifier power supply is powered from the secondary of a transformer which has a peak secondary voltage of 22V. The primary of the transformer is connected to a 50Hz, 230Vus power supply. A 2700μF filter capacitor is used. A current of 1.5 Amp is drawn from the supply (i) Sketch a schematic diagram of the setup (ii) Calculate the mean dc output voltage (ii) Assume that each diode conducts for one-twelfth...
1 Determine an equation for the efficiency (power out/power in) of a four diode bridge AC rectifier circuit. Approximate the load as one large resistor and do not assume the diode resistance is negligible. Make sure to solve the equation so only known quantities (load resistance, source voltage, ect) and not unknown quantities (currents ect) appear in it. 2. Modify your equation to include a capacitor in parallel with the load that will smooth out the resultant DC voltage and...