Problem 2 A flow of air (600 m3/h) enters an automotive A/C unit at 101.3 kPa,...
An air-water vapor mixture enters a heater-humidifier unit at 5°C, 100 kPa, 50% rh. The flow rate of dry air is 0.1 kg/s. Liquid water at 10°C is sprayed into the mixture al the rate of 0.0022 kg/s. The mixture leaves the unit at 30°C, 100 kPa. Calculate (a) the relative humidity at the outlet (b) the rate of heat transfer to the unit
(10 pts) Six-thousand cubic feet per minutes (C.F.M.) of atmospheric air at 28°C (dry bulb) having a wet bulb temperature of 23°C is to be cooled in an air conditioning system. The air conditioning system lowers the dry bulb temperature of the air to 20° C. Cooling with dehumidification is accomplished using chilled water loop. The chilled water enters the loop at 5°C at a rate of 280 kg/min and experience a 5°C temperature increase. The atmospheric pressure is 1...
Name: QUESTION 1 [25 Points] Moist air enters an air conditioning system at a dry bulb temperature T., 30 'C and relative humidity фі80% and exits at a dry bulb temperature T2 179C and relative humidity ф2.50% as shown in the figure below. The condensate exits the system at 15 °C. The mass flow rate of the dry air is 2.5 kg/s. Assume the air is at atmospheric pressure P-101.3 kPa. Cooling coils T-17 C 0-50 % Pp:-6.282 kPa Ti-30...
please solve it quickly ignore p=75 Problem 3 Part a P=57 Moist air enters the cooler of an air conditioning unit at 25 °C and a relative humidity of 70%. The cooled and dehumidified air leaves the cooler saturated at 18 °C. The temperature of condensed water is 18 °C. The pressure is constant at 101.325 kPa. The mass flow rate of the dry air is mda=67 kg/s. Use the psychometric chart to determine a) The humidity ratio at the...
Moist air at 20° c, 1 atm, and 43% relative humidity and a volumetric flow rate of 900 m/hrs. enters a control volume at steady state and flow along a surface maintained at 65 C, through which heat transfer occurs. Liquid water at 20" C is injected at a rate of 5 kg/hr and evaporates into flowing stream. For the control volume, Wa=0, and kinetic and potential energy effects are negligible. Moist air exits at 32c, 1 atm, (a) draw...
Moist air at 20°C, 1 atm, and 43% relative humidity and a volumetric flow rate of 900 m/hrs. enters a control volume at steady state and flow along a surface maintained at 65° C, through which heat transfer occurs. Liquid water at 20° C is injected at a rate of 5 kg/hr and evaporates into flowing stream. For the control volume, Wev =0, and kinetic and potential energy effects are negligible. Moist air exits at 32°C, 1 atm. (a) draw...
Air enters a turbine in steady flow at 600 kPa, 740 K, and 120 m/s. The exit conditions are 100 kPa, 450 K, and 220 m/s. A heat loss of 15 kJ/kg occurs, and the inlet area is 4.91 cm2 . Determine (a) the kinetic-energy change, in kJ/kg, (b) the power output, in kW, and (c) the ratio of the inlet- to outletpipe diameters
Moist air at 20°C, 1 atm, and 43% relative humidity and a volumetric flow rate of 900 m²/hrs. enters a control volume at steady state and flow along a surface maintained at 65°C, through which heat transfer occurs. Liquid water at 20°C is injected at a rate of 5 kg/hr and evaporates into flowing stream. For the control volume, Wev=0, and kinetic and potential energy effects are negligible. Moist air exits at 32°C, 1 atm. (a) draw the system schematic...
Example 5: Ambient air at 38°C db-temperature and 20°C wb- temperature enters an evaporative cooler with a dry air mass flow rate of 0.75 kg/s. The pressure is constant at 95 kPa. The air leaves at a db-temperature of 25°C. Calculate (i) the relative humidity of the air at inlet, (ii) the relative humidity of the air at exit, (iii) the rate of flow of water to the cooler, and (iv) the saturation effectiveness of the cooler.
A dehumidifier receives a flow of 025 kgs dry air at 28°C, 80% relative humidity, as shown in the figure. It is cooled down to 20°C as it flows over the evaporator and then is heated up again as it flows over the condenser. The standard refrigeration cycle uses R-22 with an evaporator temperature of5°C and a condensation pressure of 1600 kPa. Determine: (a) the amount of liquid water removed, (10 points) (b) the heat transfer in the cooling process,...