Homework Answers
Hey dear please provide the figure of the walls of the heat exchanger as mentioned in the question. Without figure the problem can't be solved. So I humbly request you to upload the question with figure so that you can be helped with the solution. Thank you.
Add Answer to:
Question 11 (15 points) The wall of a liquid-to-gas heat exchanger has a surface area on...
The wall of a liquid-to-gas heat exchanger has a surface area on the liquid side of...
The wall of a liquid-to-gas heat exchanger has a surface area on the liquid side of 1.8 m2 (0.6 m * 3.0 m) with a heat transfer coefficient of 255 W/m2K. On the other side of the heat exchanger wall a gas flows, and the wall has 96 thin rectangular steel fins 0.5 cm thick and 1.25 cm high (k = 3 W/m K) as shown in the figure below. The fins are 3 m long and the heat transfer...
The wall of a liquid-to-gas heat exchanger has a surface area on the liquid side of...
The wall of a liquid-to-gas heat exchanger has a surface area on the liquid side of 1.8 m2 (0.6 m 3.0 m) with a heat transfer coefficient of 255 W/m2K. On the other side of the heat exchanger wall a gas flows, and the wall has 96 thin rectangular steel fins 0.5 cm thick and 1.25 cm high (k = 3 W/m K) as shown in the figure below. The fins are 3 m long and the heat transfer coefficient...
Heat is uniformly generated at the rate of 2x 10W/m* in a wall of thermal conductivity...
Heat is uniformly generated at the rate of 2x 10W/m* in a wall of thermal conductivity 25 W/m-K and thickness 60 mm. The wall is exposed to convection on both sides, with different heat transfer coefficients and temperatures as shown. There are straight rectangular fins on the right-hand side of the wall, with dimensions as shown (L =20 mm) and thermal conductivity of 250 W/m-K. What is the maximum temperature that will occur in the wall? L tt-2 mm k=25...
The wall of a heat exchanger separates hot water at Tin 90 C with h." 80 w/m2.K from cold water a...
The wall of a heat exchanger separates hot water at Tin 90 C with h." 80 w/m2.K from cold water at Tout 10 C with h,ut 60 W/m2.K. The thermal conductivity of the heat exchanger is 180 W/m.K To extend the heat transfer area, two-dimensional ridges are machined on the cold side of the wall. This geometry causes non-uniform thermal stresses, which may become critical for crack initiation along the lines between two ridges. To predict thermal stresses, the temperature...
finite element method 2. Aluminum fins with rectangular profiles (5 mm wide and 1 mm thick) are used to remove heat...
finite element method
2. Aluminum fins with rectangular profiles (5 mm wide and 1 mm thick) are used to remove heat from a surface whose temperature is 150°C. The temperature of ambient air is 20°C. The thermal conductivity of aluminium is 168 W/m.K. The natural convective coefficient associated with the surrounding air is 35 W/m2.K. The fins are 150 mm long and the heat loss from the tip of the fin may be neglected. (a) Determine the temperature distribution along...
2.) A plane wall is made of brick with a thermal conductivity of 1.5 W/(m-K). The...
2.) A plane wall is made of brick with a thermal conductivity of 1.5 W/(m-K). The wall is 20 cm thick and has a surface area of 10 m2. One side of the wall is exposed to outside air blowing against the wall resulting in a heat transfer coefficient of 20 W/(m2-K). The other side is exposed to an air-conditioned room with a convective heat transfer coefficient of 5 W/(m2-K). a. What are the thermal resistances corresponding to conduction through...
A heat exchanger is to be designed for the following specifications: Hot gas temperature, 1145...
A heat exchanger is to be designed for the following specifications: Hot gas temperature, 1145 oC Cold gas temperature, 45 oC Unit surface conductance on the hot side, 230 W/m2-K Unit surface conductance on the cold side, 290 W/m2-K Thermal conductivity of the metal wall, 115 W/m-K Find the maximum thickness of the metal wall between the hot gas and cold gas so that the maximum temperature of the wall does not exceed 545 oC.
a rectangular fin (k= 235w/m*K) is attached to a wall and has a length of 5...
a rectangular fin (k= 235w/m*K) is attached to a wall and has a length of 5 cm, a width of 10 cm, and a thickness of 5 mm. the surface temperature of the wall is 350 degrees Celcius and the ambient air is 25 degrees celcius. what is the efficiency, the heat transfer rate, and the fin effectiveness? assume an adiabatic fin tip condition and a convection heat transfer coefficient of 154 W/m^2 * K
Problem 1 (20 marks): A 1-m x 1-m surface at 100 °C is to be cooled...
Problem 1 (20 marks): A 1-m x 1-m surface at 100 °C is to be cooled by attaching to it 5-cm long, 0.25- cm-thick square aluminum fins (k = 237 W/m- K), with an edge-to-edge distance between the fins of 0.25 cm. The temperature of the fin tip is the same as surrounding medium at 30°C, und the heat transfer coefficient on the surfaces is 35 W/m2 K. Determine: temperature at distance of 2 cm away from the base the...
The surface of a furnace wall is at a temperature of 1350oC. The outside wall temperature...
The surface of a furnace wall is at a temperature of 1350oC. The outside wall temperature is 42oC. The furnace wall is made of 25 cm of refractory material having a thermal conductivity of 1.4 W/moK. The outside wall is steel, 1 cm thick with thermal conductivity of 47 W/moK. Calculate the thickness in meters of brick to be installed in between the refractory material and steel if its thermal conductivity is 0.28 W/moK and the heat loss is not...
The wall of a liquid-to-gas heat exchanger has a surface area on the liquid side of 1.8 m2 (0.6 m * 3.0 m) with a heat transfer coefficient of 255 W/m2K. On the other side of the heat exchanger wall a gas flows, and the wall has 96 thin rectangular steel fins 0.5 cm thick and 1.25 cm high (k = 3 W/m K) as shown in the figure below. The fins are 3 m long and the heat transfer...
The wall of a liquid-to-gas heat exchanger has a surface area on the liquid side of 1.8 m2 (0.6 m 3.0 m) with a heat transfer coefficient of 255 W/m2K. On the other side of the heat exchanger wall a gas flows, and the wall has 96 thin rectangular steel fins 0.5 cm thick and 1.25 cm high (k = 3 W/m K) as shown in the figure below. The fins are 3 m long and the heat transfer coefficient...
Heat is uniformly generated at the rate of 2x 10W/m* in a wall of thermal conductivity 25 W/m-K and thickness 60 mm. The wall is exposed to convection on both sides, with different heat transfer coefficients and temperatures as shown. There are straight rectangular fins on the right-hand side of the wall, with dimensions as shown (L =20 mm) and thermal conductivity of 250 W/m-K. What is the maximum temperature that will occur in the wall? L tt-2 mm k=25...
The wall of a heat exchanger separates hot water at Tin 90 C with h." 80 w/m2.K from cold water at Tout 10 C with h,ut 60 W/m2.K. The thermal conductivity of the heat exchanger is 180 W/m.K To extend the heat transfer area, two-dimensional ridges are machined on the cold side of the wall. This geometry causes non-uniform thermal stresses, which may become critical for crack initiation along the lines between two ridges. To predict thermal stresses, the temperature...
finite element method
2. Aluminum fins with rectangular profiles (5 mm wide and 1 mm thick) are used to remove heat from a surface whose temperature is 150°C. The temperature of ambient air is 20°C. The thermal conductivity of aluminium is 168 W/m.K. The natural convective coefficient associated with the surrounding air is 35 W/m2.K. The fins are 150 mm long and the heat loss from the tip of the fin may be neglected. (a) Determine the temperature distribution along...
2.) A plane wall is made of brick with a thermal conductivity of 1.5 W/(m-K). The wall is 20 cm thick and has a surface area of 10 m2. One side of the wall is exposed to outside air blowing against the wall resulting in a heat transfer coefficient of 20 W/(m2-K). The other side is exposed to an air-conditioned room with a convective heat transfer coefficient of 5 W/(m2-K). a. What are the thermal resistances corresponding to conduction through...
Problem 1 (20 marks): A 1-m x 1-m surface at 100 °C is to be cooled by attaching to it 5-cm long, 0.25- cm-thick square aluminum fins (k = 237 W/m- K), with an edge-to-edge distance between the fins of 0.25 cm. The temperature of the fin tip is the same as surrounding medium at 30°C, und the heat transfer coefficient on the surfaces is 35 W/m2 K. Determine: temperature at distance of 2 cm away from the base the...
Most questions answered within 3 hours.
-
Task 5.2 Numerical Analysis Using Nested Loops (13 pts)
Consider the following program:
void setup()
{...
asked 8 minutes ago -
If a lossless transformer has 1000 turns for a primary winding
and 100 turns for the...
asked 16 minutes ago -
Write the net ionic equation for the precipitation reaction that
occurs when aqueous solutions of potassium...
asked 24 minutes ago -
it
should be written in c++
Your program should take numbers from the user until the...
asked 30 minutes ago -
Buses are powered by chemical reactions. Define matter and the
four states of matter. What is...
asked 48 minutes ago -
Use conservation of energy to find the velocity of a free point
charge q1 at 22cm...
asked 55 minutes ago -
First, describe policies promoted by governments of the
political right to address economic globalization. Second, describe...
asked 1 hour ago -
M2-9 Completing T-Accounts LO2-4
Following are the transactions of Dennen, Inc., for the month of
January....
asked 1 hour ago -
Write a program using python that reads from values from a text
file and plots them...
asked 1 hour ago -
Look up the density of
the metal of the object used in parts A and B...
asked 1 hour ago -
Discuss strategic considerations that Amazon and NYC politicians
had. Analyze why the deal between Amazon and...
asked 1 hour ago -
A combustion reaction is describes as a carbon source reacting
with oxygen and producing carbon dioxide...
asked 1 hour ago