4) [15 pts] Gear Train Analysis The tooth numbers for the gear train illustrated are N2...
Question 6 10 MEA351A/101/0/2019 The tooth numbers for the gear train illustrated are N2 20, N3 16, N4 30, N6 36, and N7 46. Gear 7 is fixed. If shaft a is turned through 10 revolutions, how many turns will shaft b make? = Question 6 10 MEA351A/101/0/2019 The tooth numbers for the gear train illustrated are N2 20, N3 16, N4 30, N6 36, and N7 46. Gear 7 is fixed. If shaft a is turned through 10 revolutions,...
3) (15 pts] Number of teeth and theoretical center to center distance distance from given data A 17-tooth spur pinion has a diametral pitch of 8 teethlin, runs at 1386 rev/min, and drives a gear at a speed of 462 rev/min. Find the number of teeth on the gear and the theoretical center-to-center distance. The number of teeth on the gear is The theoretical center-to-center distance is in. 4) [15 pts] Gear Train Analysis The tooth numbers for the gear...
2. The gear train in Fig. 1 has a metric module of 8 mm/tooth and the following tooth numbers: N2 = 12, N3 = 36, N4 = 24, N5 = 38, and No= 26. If the transmitted load on Gear 2 is 58 N and the transmitted power is 40 kW, the rotational speed of the Gear 6 is most nearly which value? Counterclockwise (CCW) rotations are considered positive. N - Ng Fig. 1 3 The gear train in Fig....
Q-4 For the planetary gear train shown in figure below; Draw a connectivity diagram and determine the number of DOF. Determine the magnitude and direction of n4 if n2 = 100 rpm (c.w.) and na = 100 rpm. (c.w.), and the tooth numbers of gears are N2 = 60 –T, N3 = 16-T, N4 = ? (N4 to be found!). planet gear ring gear A planet gear 3 ring gear4 sun gear 2 sun 4 2 Ibearing l gear %2...
4) (2 pts) For the compound gear train shown below assuming the input is 200 rpm cw, what is the output? Assuming the input torque is 2 lb ft, what is the output torque? 14t 84t N3 14t 84t N5 Input shaft N6 14t 70t Output shaft
4. (12 points) A compound reverted spur gear train is to be designed to reduce the speed of a 180HP engine's rotating shaft from 3500rpm to 100rpm exactly. (a) (5 points) Specify appropriate numbers of teeth (N2, N3, N4 and N5) to minimize the gearbox size. A pressure angle of 20° is used for all the gears. Interference of gears is not acceptable. (b) (5 points) If all the gears are cut with 20° full-depth system. Assume a diametral pitch...
4. (12 points) A compound reverted spur gear train is to be designed to reduce the speed of a 180HP engine's rotating shaft from 3500rpm to 100rpm exactly. (a) (5 points) Specify appropriate numbers of teeth (N2, N3, N4 and N5) to minimize the gearbox size. A pressure angle of 20° is used for all the gears. Interference of gears is not acceptable. (b) (5 points) If all the gears are cut with 20° full-depth system. Assume a diametral pitch...
4.(12 points) A compound reverted spur gear train is to be designed to reduce the speed of a 180HP engine's rotating shaft from 3500rpm to 100rpm exactly. (a) (5 points) Specify appropriate numbers of teeth (N2, N3, N4 and N5) to minimize the gearbox size. A pressure angle of 20° is used for all the gears. Interference of gears is not acceptable. (b) (5 points) If all the gears are cut with 20° full-depth system. Assume a diametral pitch of...
A compound reverted spur gear train is to be designed to reduce the speed of a 180HP engine's rotating shaft from 3500rpm to 100rpm exactly. (a) (5 points) Specify appropriate numbers of teeth (N2, N3, N4 and N5) to minimize the gearbox size. A pressure angle of 20° is used for all the gears. Interference of gears is not acceptable. (b) (5 points) If all the gears are cut with 20° full-depth system. Assume a diametral pitch of 6 teeth/in,...
A compound reverted spur gear train is to be designed to reduce the speed of a 180HP engine's rotating shaft from 3500rpm to 100rpm exactly. (a) (5 points) Specify appropriate numbers of teeth (N2, N3, N4 and N5) to minimize the gearbox size. A pressure angle of 20° is used for all the gears. Interference of gears is not acceptable. (b) (5 points) If all the gears are cut with 20° full-depth system. Assume a diametral pitch of 6 teeth/in,...