4) (2 pts) For the compound gear train shown below assuming the input is 200 rpm...

Question

Question

4) (2 pts) For the compound gear train shown below assuming the input is 200 rpm cw, what is the output? Assuming the input t

Answer 1

Answer #1

Griven -that smitiny teet 2 Pnoduat of teatt,of .Phanimitting

Answer 2

Similar Homework Help Questions

In the gear train shown below, the pinion 2 is the driver, and gear 5 is...

In the gear train shown below, the pinion 2 is the driver, and gear 5 is the output gear. All gears are spur gears has a module of 2.5mm and pressure angle of 200. The number of gear teeth are: N2 - 14, N3 - 84, N4 - 14, N5 - 70 teeth. The gear set transmits the power of 1.5KW at a constant angular velocity of XX rev/min. Where XX is the last two digits of your University ID...
Homework 6: The figure below shows a gear train where gear 1, on shaft a (input...

Homework 6: The figure below shows a gear train where gear 1, on shaft a (input shaft), drives gear 2 with 32 teeth (denoted 32T) on shaft b, gear 3 (20T) also is on shaft b and drives gear 4 (507) on shaft c (output shaft). The pitch diameter of gears 1 and 2 are d = 24 mm and d = 48 mm. The center distance between gears 3 and 4 (distance between shafts b and c is 70mm....
Machine design 1 Name Application 10 The compound reverted gear train shown below is used to...

Machine design 1 Name Application 10 The compound reverted gear train shown below is used to reduce the speed of the input (gear 2) to the output gear 5. Your objective is to develop a design for this gear train be specify the gear teeth. There are several requirements to keep in mind and the objective is to reduce the overall size dimension Y Requirements . . . . Shall deliver 20 HP Input speed shall be 1750 RPM (adjustable)...

2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5...

2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5 hp electric motor. All of the gears have a diametral pitch of 8 teeth per inch. i) What is the ratio of output torque (Gear 4) to input torque (Gear 1)? j) Is it a coincidence that it is the same as the answer in 1 An input shaft drives Gear 1 with 20 teeth at 1800 rpm which mates with the 80-tooth Gear...
4) [15 pts] Gear Train Analysis The tooth numbers for the gear train illustrated are N2...

4) [15 pts] Gear Train Analysis The tooth numbers for the gear train illustrated are N2 = 12, N3 = 16, N4 = 30, N6 = 36, and N7 = 38. Gear 7 is fixed. If shaft a is turned through 16 revolutions, how many turns will shaft b make? E41 [6] 5 31 -2- -7 b The shaft b turns revolutions.
2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5...

2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5 hp electric motor. All of the gears have a diametral pitch of 8 teeth per inch. e) What is the transmitted force between Gears 1 and 2, in lbf? f) What is the torque of Gear 1, in in-lbf? g) What is the torque of Gear 2? h) The torque of Gear 2 and 3 are the same. What is the torque of Gear...

2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5...

2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5 hp electric motor. All of the gears have a diametral pitch of 8 teeth per inch. a) What are the diameters of Gears 1, 2, 3, and 4? b) What is the pitch-line velocity of Gear 1, in ft/min? c) Is the pitch-line velocity of Gear 2 the same as Gear 1? d) What is the pitch-line velocity of Gear 3 (and, therefore, Gear...
For the planetary gear train in the Figure, ω7 = 0 RPM, ω3 = ωARM =...

For the planetary gear train in the Figure, ω7 = 0 RPM, ω3 = ωARM = 164 RPM and the known number of teeth for each gear are: N2 = 24, N5 = 32, N6 = 67 and N7 = 69. What is the angular speed of gear 2 (ω2) in RPMs? 6 5 3 4 LIL 2) WIIIITT 7
Answer the following questions about the illustrated gear train. Assume the input shaft has an angular...

Answer the following questions about the illustrated gear train. Assume the input shaft has an angular velocity of 100RPM CCW and 100lb-ft of torque. Show all work and circle answers. (a) (5 points) What is the overall gear ratio between the input and output shaft?! (b) (5 points) What is the torque of the output shaft assuming an ideal system? (c) (5 points) What is the direction that the output shaft is rotating? Clockwise CWyor counterclockwise (CCW)? Draw the direction...

2. The gear train in Fig. 1 has a metric module of 8 mm/tooth and the...

2. The gear train in Fig. 1 has a metric module of 8 mm/tooth and the following tooth numbers: N2 = 12, N3 = 36, N4 = 24, N5 = 38, and No= 26. If the transmitted load on Gear 2 is 58 N and the transmitted power is 40 kW, the rotational speed of the Gear 6 is most nearly which value? Counterclockwise (CCW) rotations are considered positive. N - Ng Fig. 1 3 The gear train in Fig....