can i have example report on open ended lab for concrete design ???
if you have any doubt regarding this please let me know if you understand the solution than please give me a thumbs up thanks
These questions are three at the end of my lab report that I can make neither heads nor tails of. I'm including all the data I have, as well as the lab report information I have. I just need an answer to put down for the report for each question, so make your best attempt at what the answer might be. Thanks. :) For Question Two:
Experimental Design Lab? Experimental Design Lab Report Sheet Name Case Study is 25 points Lab Report is 50 points Teamwork is 25 points A: Answering the Question Question: What is the percent yield in your reaction of sodium carbonate and calcium chloride? (Hint: Do not use all of the solutions in case you need to redo or modify the experiment) Procedures: Quantitative Results: Show all your work with any calculations.
Hello, I have a question about my post lab report. I used .1g of trans-3-phenyl-2-propanoic acid and 1.5mL of methylene chloride. Later I added 0.8mL of 1M bromine solution to it. I ended up getting the anti stereoisomer of 2,3-dibromo-3-phenylpropanoic acid. The product that I ended up weighing out was 0.0380g. Can you please calculate out the % yield for it? Thanks!
Example CVEG 4303: Reinforced Concrete I One-Way Slabs A 5" thick concrete slab is reinforced for tension with #4 bars spaced at 7". The effective depth is 4" Grade 60 bars and 8,ooo psi concrete will be used. 1.) Determine the design bending strength (фМп) of the slab. 2.) Check that ACI requirements for rebar strain, rebar spacing, and minimum reinforcement are met (ACI 7.3.3.1, ACI 24.3.2, and ACI 7.6.1.1 respectively). Note: Do not need to check temperature and shrinkage...
RENFORCEMENT CONCRETE DESIGN (ACI-Code 2019). Reinforced Concrete Design Example 1: Using the ACI-Code approximate structural analysis, design for a warehouse, a continuous one-way solid slab supported on beams 4.0 m apart as shown in Figure. Assume that the beam webs are 30 cm wide. The dead load is 3 kN/m² in addition to the own weight of the slab, and the live load is 3 kN/m². Use fcº=28MPa, fy= 420MPa 8.0 m 4.0 m 4.0 m 4.0 m
Compare the characteristics of open-ended and closed-ended questions. Give an example of a subject that is amenable to each type of question. Describe the usefulness of each type of question as evidence for nursing practice. Example of Subject Usefulness as evidence for nursing practice Types of Questionnaire Open-ended Closed-ended Indicate whether the following is Qualitative Data or Quantitative Data: 1. Questionnaires 2. Interviews 3. Participant Observation 4. Focus Groups 5. Surveys
I have a lab report due on the chromatography of leaves, and the solvent used was propanone which is a polar value and should give a low Rf, however I got a high Rf (0.70) and am not sure how to explain that on my report.
Provide an example of an open ended and a close ended question that you may ask sfaff nures in order to study the relationship between staff & patient satisfaction
Types of Questionnaire Open-ended Example of Subject Usefulness as evidence for nursing practice Closed-ended
NEC2103-Engineering Materials and Construction Example Mix Design Problems Question 2. Design a concrete mix using fly ash from the following data for use as fly ash concrete blocks. Use the British DOE method to calculate the required amounts (in kg/m') of water, cement, course aggregate and fine aggregate. Characteristic 28 days mean strength 25 MPa Risk factor may be taken =1.65 Standard deviation = 5.0 The max. size of coarse, aggregate C.A. = 20 mm 40% F.A. passes through 600...