Homework Answers
P.S: If you are having any doubt, please comment here, I
will surely reply you.Please provide your valuable feedback by a
thumbsup. Your thumbsup is a result of our efforts. Thanks in
advance!
Add Answer to:
Design an electronic lock system. This system has 2 inputs: A and B. This system will...
Name: (4) (10 pts) Design a Moore FSM that has one input A and one output Y, and the output Y should be 1 if A has...
Name: (4) (10 pts) Design a Moore FSM that has one input A and one output Y, and the output Y should be 1 if A has been 101 during the most recent three consecutive clock cycles or A has been 1 during the two most recent consecutive clock cycles. You only need to write down your state transition diagram. (5) (6 pts) Consider the following sequential circuit. Each two-input OR gate has a propagation delay of 130ps and a...
(20 pts.) For the following circuit, the timing characteristics of the components are summarized below. .Flip-flop:...
(20 pts.) For the following circuit, the timing characteristics of the components are summarized below. .Flip-flop: clock-to-Q maximum delay tpcq 40ps, clock-to-Q minimum delay tec 30ps, setup time tsetup 50ps, hold time thold 60ps Logic gate (each AND, OR, Inverter): propagation delay tpd 35ps, contamination delay ted25ps. FFl Fr3 CLK OUT FF2 CLK Suppose that there is no clock skew. What is the maximum clock frequency of this a. circuit? b. How much clock skew can the circuit tolerate before...
3) Recall that a flip-flop is built from 2 latches cascaded in the master-slave configuration as...
3) Recall that a flip-flop is built from 2 latches cascaded in the master-slave configuration as shown in Figure S. Assume that each latch has a D-to-Q propagation delay of 5ns and a D to-Q contamination delay of 2ns. The inverter has a propagation delay of 5ns and a contamination delay of ens. If you were the designer of this flip-flop, what would you report as the setup time and hold time of the flip-flop? D latch (master) D latch...
(b) Using a timing diagram showing the clk, Q1 and D2 signals, explain the following timing const...
(b) Using a timing diagram showing the clk, Q1 and D2 signals, explain the following timing constraints for the circuit shown in Figure 2.1 cqtcd 2 old where tod is the contamination delay of the combinational logic 7 marks reg2 reg1 Combinational D2 logic clk. clk Figure 2.1 (c) In the circuit shown in Figure 2.2, the flip-flops have a clock-to-Q contamination delay of 30 ps and a propagation delay of 80 ps. They have a setup time of 50...
1. a) Complete the waveform templates for the Master –Slave D-flip-flop below with given D, CLK,...
1.
a) Complete the waveform templates for the Master –Slave
D-flip-flop below with given D, CLK, CLEAR, and PRESET signals.
Neglect the propagation delays.
b) Does it have positive or negative edge triggering with
respect to CLK?
c) Are the asynchronous PRESET and CLEAR active-high or
active-low?
2. Enabling of data load in the D-flip-flop was implemented with
a 2-to-1 multiplexer as show below. The D-flip-flop has the
positive edge triggering and the active-low asynchronous clear.
a) Is the Enable...
1. Complete the waveform of Qoutput based on the given set of inputs. C is the...
1. Complete the waveform of Qoutput based on the given set of inputs. C is the clock input. (2 marks) C. I к e 2. Complete the waveform of Qoutput from a D flip-flop based on the given set of inputs. C is the clock input. Notice this flip-flop has two asynchronous inputs. Notice the overhead bars above some signal names. (2 marks) c 30 Ro D e 3. Both J and Kinputs of a JK flip-flop are tied to...
2. A four-bit addition machine is built with four full adders such that the carry out...
2. A four-bit addition machine is built with four full adders
such that the carry out of the first adder is the carry in to the
second adder, and the carry out of the second is the carry in to
the third, and so on as shown in Figure 2.
The machine has input and output registers and must complete the
addition in one clock cycle.
Each full adder has the following propagation delays: 20 ps from
Cin to Cout...
3. (16 pts.) A sequential circuit design is shown in the following diagram CLK CLK Frt Trl Frl FF1 D-FF clk-to-q propagation delay tpcq 15 ps D-FF clk-to-q contamination delay tccq-10 ps D-FF dat...
3. (16 pts.) A sequential circuit design is shown in the following diagram CLK CLK Frt Trl Frl FF1 D-FF clk-to-q propagation delay tpcq 15 ps D-FF clk-to-q contamination delay tccq-10 ps D-FF data setup time ts-15 ps D-FF data hold time th = 10 ps Gate 2-input NAND 2-input NOR 2-input XOIR NOT Tpd(ps) Tea(ps) 15 25 35 10 10 15 25 (8 pts.) Calculate the maximum clock frequency for reliable operation assuming there is no clock skew (8...
QUESTION 3 The following synchronizer circuit is composed of flip-flops with a setup time of 2...
QUESTION 3 The following synchronizer circuit is composed of flip-flops with a setup time of 2 ns, a hold time of Ons, and a clock- to-Q delay of Ons B D-FF D-FF A Q S CLK Given the delays above, analyze the circuit above, and fill out the timing diagram below clk A B S clk A O B S. clk B S. QUESTION 4 Analyze the timing diagram from the previous problem. Assuming that A always changes at a...
Used 2. (10 points) Design a sequential circuit, which has the potential of being combinational l...
please answer the following?
used 2. (10 points) Design a sequential circuit, which has the potential of being combinational lock" if the number of inputs is expanded. The circuit has four inputs, labelet as reset, codeo, codel, and code2, and one output, labeled as match. Binary bits are coming to the four inputs sequentially, one bit at a time for each clock cycle. After reset - 1 for one clock cycle, the circuit searches for the first occurrence of the...
Name: (4) (10 pts) Design a Moore FSM that has one input A and one output Y, and the output Y should be 1 if A has been 101 during the most recent three consecutive clock cycles or A has been 1 during the two most recent consecutive clock cycles. You only need to write down your state transition diagram. (5) (6 pts) Consider the following sequential circuit. Each two-input OR gate has a propagation delay of 130ps and a...
(20 pts.) For the following circuit, the timing characteristics of the components are summarized below. .Flip-flop: clock-to-Q maximum delay tpcq 40ps, clock-to-Q minimum delay tec 30ps, setup time tsetup 50ps, hold time thold 60ps Logic gate (each AND, OR, Inverter): propagation delay tpd 35ps, contamination delay ted25ps. FFl Fr3 CLK OUT FF2 CLK Suppose that there is no clock skew. What is the maximum clock frequency of this a. circuit? b. How much clock skew can the circuit tolerate before...
3) Recall that a flip-flop is built from 2 latches cascaded in the master-slave configuration as shown in Figure S. Assume that each latch has a D-to-Q propagation delay of 5ns and a D to-Q contamination delay of 2ns. The inverter has a propagation delay of 5ns and a contamination delay of ens. If you were the designer of this flip-flop, what would you report as the setup time and hold time of the flip-flop? D latch (master) D latch...
(b) Using a timing diagram showing the clk, Q1 and D2 signals, explain the following timing constraints for the circuit shown in Figure 2.1 cqtcd 2 old where tod is the contamination delay of the combinational logic 7 marks reg2 reg1 Combinational D2 logic clk. clk Figure 2.1 (c) In the circuit shown in Figure 2.2, the flip-flops have a clock-to-Q contamination delay of 30 ps and a propagation delay of 80 ps. They have a setup time of 50...
1.
a) Complete the waveform templates for the Master –Slave
D-flip-flop below with given D, CLK, CLEAR, and PRESET signals.
Neglect the propagation delays.
b) Does it have positive or negative edge triggering with
respect to CLK?
c) Are the asynchronous PRESET and CLEAR active-high or
active-low?
2. Enabling of data load in the D-flip-flop was implemented with
a 2-to-1 multiplexer as show below. The D-flip-flop has the
positive edge triggering and the active-low asynchronous clear.
a) Is the Enable...
1. Complete the waveform of Qoutput based on the given set of inputs. C is the clock input. (2 marks) C. I к e 2. Complete the waveform of Qoutput from a D flip-flop based on the given set of inputs. C is the clock input. Notice this flip-flop has two asynchronous inputs. Notice the overhead bars above some signal names. (2 marks) c 30 Ro D e 3. Both J and Kinputs of a JK flip-flop are tied to...
2. A four-bit addition machine is built with four full adders
such that the carry out of the first adder is the carry in to the
second adder, and the carry out of the second is the carry in to
the third, and so on as shown in Figure 2.
The machine has input and output registers and must complete the
addition in one clock cycle.
Each full adder has the following propagation delays: 20 ps from
Cin to Cout...
3. (16 pts.) A sequential circuit design is shown in the following diagram CLK CLK Frt Trl Frl FF1 D-FF clk-to-q propagation delay tpcq 15 ps D-FF clk-to-q contamination delay tccq-10 ps D-FF data setup time ts-15 ps D-FF data hold time th = 10 ps Gate 2-input NAND 2-input NOR 2-input XOIR NOT Tpd(ps) Tea(ps) 15 25 35 10 10 15 25 (8 pts.) Calculate the maximum clock frequency for reliable operation assuming there is no clock skew (8...
QUESTION 3 The following synchronizer circuit is composed of flip-flops with a setup time of 2 ns, a hold time of Ons, and a clock- to-Q delay of Ons B D-FF D-FF A Q S CLK Given the delays above, analyze the circuit above, and fill out the timing diagram below clk A B S clk A O B S. clk B S. QUESTION 4 Analyze the timing diagram from the previous problem. Assuming that A always changes at a...
please answer the following?
used 2. (10 points) Design a sequential circuit, which has the potential of being combinational lock" if the number of inputs is expanded. The circuit has four inputs, labelet as reset, codeo, codel, and code2, and one output, labeled as match. Binary bits are coming to the four inputs sequentially, one bit at a time for each clock cycle. After reset - 1 for one clock cycle, the circuit searches for the first occurrence of the...
Most questions answered within 3 hours.
-
Industry: Telecommunications in India
Here, you need to discuss the sources of the growth pattern
and...
asked 7 minutes ago -
Hydrobromic acid
dissolves solid iron according to the followiaung reaction:
Fe(s)+2HBr(aq)→
FeBr2(aq)+ H2(g)
Part A. What...
asked 1 hour ago -
Verify the following vector identity in SPHERICAL
COORDINATES.
div(curl(A)) = 0
asked 3 hours ago -
The work function (Φ) for a metal is 7.50×10-19 J.
What is the longest wavelength (nm)...
asked 4 hours ago -
1. Would the following procedural changes cause the
calculated mass percent Ni2+ ion in Ni(NH3)nCl2 to...
asked 5 hours ago -
1. Why does the voltage of the capacitor vary with frequency?
where does this missing voltage...
asked 6 hours ago -
p p please write each step out clearly
3. A manager of a company is considering...
asked 5 hours ago -
On October 1, Ebony Ernst organized Ernst Consulting; on October
3, the owner contributed $83,540 in...
asked 7 hours ago -
A.)As an electron moves through a region of space, its speed
decreases from 9.60 × 106...
asked 7 hours ago -
In java with the netbeans program do:
Through object programming
Create a class "ContadorP", which is...
asked 7 hours ago -
Pattern Corporation acquired all of Science
Company's outstanding stock on January 1, 2016 for $600,000 cash....
asked 7 hours ago -
Here are all accounts Tyler Co. maintains.
Tax expenses $4,750
Common stocks $48,840
SG&A expenses $2,500...
asked 7 hours ago