5. A logic high output PD7 turns on a fan. The TMP36 sensor is used with...
11.5 A temperature sensor is connected to a 16F873A ADC input. The sensor has an output of 40 mV/?C. The ADC operates with a 4.096 V reference. (a) For a certain temperature value, the ADC output reads 1010011100. What is the equivalent temperature for this reading? (b) The measured temperature is to be displayed on a digital display, showing values in the range 00.0?C to 99.9?C. Describe what data manipulation steps can be taken to achieve this, using fixed-point arithmetic...
9. Consider a light sensor that is in a "Smart Car". The light sensor is used for turning the headlights on when light sensor does not detect any light. When there is no light on the sensor, the output of the LDR is 15 and when it detects a light, the output is 200. Consider the LDR output is read into à variable "sensorValue". Write a conditional statement that the lights turn on when it is dark. You can use...
PLC 7. Given a temperature control application where if the temperature at a sensor becomes closed when the temperature is below 55°F. Use a 15 minute timer/delay relay to keep the heater coil on once the temperature is below 55° F. Write a ladder logic program to achieve this. Temp switch Timer 15 min Keep output high for 15 min once activated Heater Coil Turn on to increase temperature Closed if <55 F PLC 7. Given a temperature control application...
ANSWER THE QUESTION IN THE END READING THE DIAL WITH THE AVR ATMEGA16 MICROCONTROLLER #include <axc/ie.h> int main(void) int ads.valusimm 1/Variable used to store the value read from ADC DDRB = (1<<PBC); //PB® is an output ADMUX = (1<<REFSO); ADMUX &= -(1<<REFS1mm //Axcs(+5v) as voltage reference ADCSRA != ((1<<ADPS2) (1<<ADP51)|(1<<ADPS0)); //ecessalec at 128 ADCSRA |= (1<<ADEN); 1/Power up the ADC ADCSRA - (1<<ADSC); 1/Start converting ADCSRA |= (1<<ADATE); // finish the conversion automatically while(1) { //The infinite loop adc value...
7. Given a temperature control application where if the temperature at a sensor becomes closed when the temperature is below 55°F. Use a 15 minute timer/delay relay to keep the heater coiron once the temperature is below 55°F. Write a ladder logic program to achieve this Temp switch Timer 15 min Keep output high for 15 min once activated Heater Coil Turn on to increase temperature Closed if <55 F g 1 input switch (push button), write a plc ladder...
A resistive temperature sensor Rv (calibration curve shown below) is used to measure the temperature of a process using Wheatstone bridge (Fig. 1). When the bridge is balanced, EO = OV. Then the Ry is inserted into a process whose temperature is 100C. Assume Ei = 10V, R1 = R2 = R3 = 4k12. 1. At which temperature the bridge is balanced? How much is EO at balanced mode? 2. Find the bridge output voltage E, a 3-significant figure voltmeter...
after completing the truth table, write equations for each output segment. ( through Sa-Sg so 7 equations) using k-maps next translate your equations into logic gates using only ONE design for all the equations. 7-segment 4, display7 decoder S Figure 3.7-segment display decoder To design your seven-segment display decoder, you will first write the truth table specifying the output values for each input combination. We have started the truth table for you in Table 1. For example, when the input...
using matlab to find steps 1-10 Calibration and sensing Consider a thermistor temperature sensor (Fig. 1) with a pull-up resistor R1 connected to a 10-bit analog-to-digital (ADC) converter (a full scale No-210-1=1023 counts corresponding to the reference voltage Vref). The thermistor is used to measure temperature in the total input span from -10°C to 110°C. knots n(t VO R1 A/D GND Temperature Fig. 1 The output count of the thermistor measurements circuit can be modeled by a nonlinear function of...
. What is a programmable logic controller (PLC)?12. The , Identify four tasks in addition to relay switching operations that PLCs are capable performing. 3. List six distinct advantages that PLCs offer over controller operates in real time. What does this mean? of performing 13. Answer the following with reference to the f conventional relay-based control systems. control PLC ladder logic diagram of Figure 1-21 this etary PLC architecture. 5. State two ways in which LVO is incorporated into 4,...
Please help with this code For the following problem write a Matlab® script file with clear commentary for each line of code. Your script should: Load the data in the problem as a text file. Calculate the statistics using Matlab functions. Solicit input from the user of the reading (for example, 137 degrees as stated in the problem). In another word, the reading should not be fixed in the script and has to be entered and saved from the command window...