*** Using the computer program MultiSIM to complete this assignment please ***
*** Using the computer program MultiSIM to complete this assignment please *** 1. Construct a 6...
Just need the code for the random counter,Thanks Objective: In this lab, we will learn how we can design sequential circuits using behavioral modelling, and implementing the design in FPGA. Problem: Design a random counter with the following counting sequence: Counting Sequence: 04 2 9 168573 Design Description: The counter has one clock (Clock), one reset (Reset), and one move left or right control signal (L/R) as input. The counter also has one 4bit output O and one 2bit output...
solve 1 2 and 3 Problems 1 and 2 require a 7-segment display. You may want to re-use the display driver you developed in Lab 3. Use a push-button as the clock - the pushbuttons are debounced, whereas the slide switches are not. Remember to provide columnsfor lest data in your state lables (use the observed next state as the test data in problems I and 2, and the observed next state and preseni output as the lest data in...
don't make use of truth table or logical operation University nology LEARNING OUTCOME 3 A learner is expected build a simple circuit that uses a PIC16F627A micro-controller to decode binary numbers to BCD counter that will display a zero to 9. Make sure that you download the data sheet for the type of 7 segment you have. The circuit must be able to convert the binary numbers from the four switches to a BCD that is to be displayed on...
Could you please show me how I can drw those circuits. please using (NI Multisim 14) Optocoupler Objectives Use an ohmmeter to determine the condition of the optoisolator. Observe the operation of an optocoupler. Determine the maximum frequency response of the optocoupler. Required Materials (1) Dual DC power supply (1) Function generator (1) Oscilloscope (2) Multimeters (1) Optocoupler (ECG3040) (1) 3.9ΚΩ resistor (1) 220 resistor Introduction An optoisolator is a hybrid integrated circuit that contains an LED on one side...
Program is for an Arduino 1. Add the letters “A”, “b”, “c”, “d”, “E”, “F” to your homework program. Continually display “0123”, “4567”, “89Ab”, “cdEF” with a one second delay between each one. HINT: Expand pickNumber() to use numbers 10-15 (a-f in hex). Create new functions for a-f. (THIS IS THE CODE FROM THE HOMEWORK) /*************************************** name:Stopwatch function: you can see the number increases by one per second on the 4-digit 7-segment display. ***********************************/ //Email:[email protected] //Website:www.sunfounder.com /**************************************/ #include //the pins...
I need help with a C++ assignment: Write a program containing the following: 1. Variable Definitions only as (DieRoll, Guess, cnt1, cnt2) followed by this statement: srand((unsigned int)time (NULL)); which will give the random number generator a random starting point. Note: srand and rand require the TIME.H (or iomanip) cnt1 and cnt2 will be used in Chapter 5 drop box as counters for loops. Do NOT create additional variables. Points will be taken off for any additional variable creation. 2....
Can someone please show me a circuit diagram so i can see how to construct this on a bread board i am id 6 yhanks in advance EEET-2251: Course & Projoct Guide 2018 EEET-2251: Cousc &Projoct Guide 2018 affic Light Controller A single switch must set your HC74 based state machine to the initial state (the U state This lab will get you to design a simple controller for a pedestrian crossing based on synchronous digital logic. You will master...
In this lab, you will design a finite state machine to control the tail lights of an unsual car. There are three lights on each side that operate in sequence to indicate thedirection of a turn. Figure ! shows the tail lights and Figure 2 shows the flashing sequence for (a) left turns and (b) right rums. ZOTTAS Figure 28:8: BCECECece BCECECECes BCECECECB BCECECBCB 8888 Figure 2 Part 1 - FSM Design Start with designing the state transition diagram for...
There is an example below Now that everything is working you can try the following exercises. To complete them you will need to refer to the documentation in Appendix A The MiteASM Assembler and Appendix B The MiteFPGA Processor. Write an assembly language program for an over counter for a cricket umpire. This should 1. display a count on the 7-segment display. The count should increase by 1 when button 0 is pressed. It should reset to 0 when button...
6-1 Test and debug the Invoice Application i need help with this please.. all help is appreciated Source code Java: import java.util.Scanner; import java.text.NumberFormat; public class InvoiceApp { public static void main(String[] args) { Scanner sc = new Scanner(System.in); String choice = "y"; while (!choice.equalsIgnoreCase("n")) { // get the input from the user System.out.print("Enter customer type (r/c): "); String customerType = sc.next(); System.out.print("Enter subtotal: "); double subtotal = sc.nextDouble(); // get the discount percent double discountPercent = 0.0; switch(customerType) {...