Here is the answer in below images...
In this lab, you will design a finite state machine to control the tail lights of...
4) (3 points) You are asked to design a finite state machine (FSM) to control the tail-light of a 1965 Ford Thunderbird automobile. There are three lights on each side: i) Left: LA, LB, LC; ii) Right: RA, RB, RC. Corresponding to a Left (L) or a Right (R) turn signal, the flashing sequence is as shown in the figure below. [For example, when the left turn signal is activated, all the lights are off, then LA turns on, then...
2. (18 pts.) Tail lights of the car shown below controlled by a sequential circuit. There are three lights on each side, and for turns they operate in sequence to show the turning direction. The control circuit has two inputs signals, LEFT and RIGHT that carry the drivers request for a left turn or a right turn. It also has an emergency flasher input, HAZ, that requests the tail lights to be operated in hazard mode all six lights flashing...
Problem: Design a clocked synchronous state machine with two inputs A, and B, and a single output Z that is 1 is: .A had the same value at each of the two previous clock ticks, or B has been 1 since the last time that the first condition was true. In-Lab 1. 2. 3. 4. For the finite state machine (FSM), identify the minimum number of states required Draw the state transition diagram Complete the state transition table Derive the...
3. Finite State Machine. Using a ROM based finite state machine (FSM), design a bi-directional repetitive 3-bit modulo-6 (0,1,2,3,4,5) counter (see Table 3). The design has one input named Dir and three outputs named B2, B1 and BO. The outputs (B2, B1 and BO) are dependent upon being in the present state only. After each clock pulse, when Dir is at logic "O', the outputs (B2, B1, BO) step through the count sequence in following order:- 0,1,2,3,4,5. After each clock...
Write a behavioral Verilog module for a 4-bit Johnson counter that has 8 states. The counter loads the "0000" state if reset is low. The counter should start and end with this state. Write a testbench to verify the correctness of the 4-bit Johnson counter. The testbenclh should have a clock with a period of 20ns and a reset signal. The testbench should store the 4-bit binary outputs of the counter in a file, which will be used to provide...
please answer question 4 (all parts of question4 please) will rate! 3. (30 pts) Design a 2-bit Gray code generator that ropetitively delivers the sequence 00301911-10-00when the input signal UP- 1,or in reverse order 009 10기け01 →00→ when UP-0. Your design should include an asynchronous low. active reset operation: the FSM goes to 00 state when a reset signal is applied In addition to the state output z[1). 2[0]. there is a carry/borrow output bit e which is I when...
Your supervisor has assigned you to build a finite state machine (FSM) in C code to control the operation of a gas pump. You determine that the required states are: . idle, payment card verifying payment approved, payment denied, nozzle removed, waiting for grade selection, e pumping. finalizing transaction (i.e. the nozzle has been returned) . emergency (someone drove off before removing the nozzle, fire detected, etc. The first thing you decide to do is to create a custom C...
Just need the code for the random counter,Thanks Objective: In this lab, we will learn how we can design sequential circuits using behavioral modelling, and implementing the design in FPGA. Problem: Design a random counter with the following counting sequence: Counting Sequence: 04 2 9 168573 Design Description: The counter has one clock (Clock), one reset (Reset), and one move left or right control signal (L/R) as input. The counter also has one 4bit output O and one 2bit output...
Finite state machine (FSM) counter design: Gray codes have a useful property in that consecutive numbers differ in only a single bit position. Table 1 lists a 3-bit modulo 8 Gray code representing the numbers 0 to 7. Design a 3-bit modulo 8 Gray code counter FSM. a) First design and sketch a 3-bit modulo 8 Gray code counter FSM with no inputs and three outputs, the 3-bit signal Q2:0. (A modulo N counter counts from 0 to N −...
9. Product State Graph ou are asked to design a sequence detector to detect the input codes 10 and 01. The input of the circuit is and the output is Z, which only changes at a clock edge. Overlaps must also be detected. Z only changes at the clock edge . [2%] A. Restate the problem by circling the most appropriate term within the parentheses 1. The circuilt type is (combinational- asynchronous- FSM). 2. The subcategory of the circuit is...