Homework Answers
(a)
From table 11.2, corresponding to 30mm bore we have C10 = 195KN and C0 = 10KN
Also Fa = 2KN and Fr = 5KN
Now Fa/C0 = 2/10 = 0.2
From Linear interpretation we find value of e at Fa/C0 = 0.2 is 0.351
Fa/(VxFr) = 2 / (1x5) = 0.4
So Fa/(vxFr) > e
So
Fe= X2xVxFr + Y2xFa
From Linear interpretation we find value of Y2 at e = 0.351 is 1.266
Fe = 0.56 x 1 x 5 + 1.266 x 2 = 5.332 KN . which is the equivalent radial load.
Add Answer to:
tables that would help u
Q-4 An 02-series single-row deep-groove ball bearing with a 30-mm bore...
mechanical Desgin 2 11 - 20: A single-row deep-groove ball bearing with a 65-mm bore (see...
mechanical Desgin 2
11 - 20: A single-row deep-groove ball bearing with a 65-mm bore (see Tables 11-1 for specifications) is loaded with a 3-KN axial load and a 7-KN radial load. The outer ring rotates at 500 rev/min. (a) Determine the equivalent radial load that will be experienced by this particular bearing. (b) Determine whether this bearing should be expected to carry this load with a 95 percent reliability for 10 kh.
Table 11-2 Dimensions and Load Ratings for Single-Row 02-Series Deep-Groove and Angular-Contact Ball Bearings Load Ratings,...
Table 11-2 Dimensions and Load Ratings for Single-Row 02-Series Deep-Groove and Angular-Contact Ball Bearings Load Ratings, kN Fillet Shoulder Width, Radius, Deep Groove Angular Contact Bore, OD, Diameter, mm ds C10 с. Сто Co mm mm mm mm 10 30 9 0.6 12.5 27 5.07 2.24 4.94 2.12 12 32 10 0.6 28 6.89 3.10 7.02 3.05 14.5 15 35 11 0.6 17.5 31 7.80 3.55 8.06 3.65 17 40 12 0.6 19.5 34 9.56 4.50 9.95 4.75 20 47...
HW Bearings 4 Required information A 02-series single-row deep-groove ball bearing is to be selec...
HW Bearings 4 Required information A 02-series single-row deep-groove ball bearing is to be selected from Table 11-2 for the application conditions specified in the lable. Assume Table 11-1 is applicable if neetded. The value of radial oad F-10 kN, axial led Fa-5 kN, design life 12 kh and 300 revimin, ring rotation factor V-1.0, and reliabilty Ro-0.98 ら:5kN- actor V 25 NOTE. This is a multi-part question Once an answer is suibrnited, you waill be unable to return t...
A Bearing A is a deep groove type and bearing B is an angular contact sölid...
A Bearing A is a deep groove type and bearing B is an angular contact sölid shaft is mounted on two Single-Row 02-Seri es Ball bearings The radial loads are Fr2472N, FR 3422N, axial load is Pa and the minimum static rating is 11000N. The design characteristics are speed of 500rpm, d application factor is 1.25,xo 0.02,-4.459, b- 1.483,a reliability of each bearing is to be at least 95.0%. The inner rings sign life of 10000hr, manufacturer rated life 10....
5. Bearing life prediction. (20 points) A 02-series Score: with a 50 mm bore (sce Tables 11-1 and 11-2 for specific...
5. Bearing life prediction. (20 points) A 02-series Score: with a 50 mm bore (sce Tables 11-1 and 11-2 for specifications) is loaded with a 2.6 kN radial load and a 4.17 KN axial load. The inner ring rotates at 1450 rev/min. The application es single-row angular contact b factor is a,1.3. C1) Determine the equivalent radial load that will be experienced by this particular bearing. (2) Determine the predicted life (in hours) that this bearing could be _expectedtogvein this...
A 02-series angular contact ball bearing with a 10-mm bore is loaded with a 0.3604 kN axial load and 100 kN radial load. The inner ring rotates at 8000 rev/min and working 2000-hour service. For Rd =...
A 02-series angular contact ball bearing with a 10-mm bore is
loaded with a 0.3604 kN axial load and 100 kN radial load. The
inner ring rotates at 8000 rev/min and working 2000-hour service.
For Rd = 93% and af = 1.
(a) Determine the equivalent radial load that will be
experienced by the bearing.
(b) Consider a rating rated life of 10^6 revolutions find C10
load experienced by bearing and calculate the factor of safety in
carrying the load...
) Given: You have to use a series 02 deep grove ball bearing with a C10...
) Given: You have to use a series 02 deep grove ball bearing with a C10 rating of 30.7KN and a catalog life rating of 106 cycles. The inner ring rotates and the reliability is 90%. You want the bearing to last 4000hrs at 1200RPM. What is the Fo (desgin rating). Given: You have to use a standard series 02 deep groove ball bearing. Your design radial force is 650Lb and your design life is 25Khrs. The torque being transmitted...
HW Bearlngs Required information A 02-series single-row deeo-groove oall bearing is to oe selected trom lable...
HW Bearlngs Required information A 02-series single-row deeo-groove oall bearing is to oe selected trom lable 11-2 tor t conditions specited in the tableme Talble 11-1 is applicable if needed The value of raa oad Fr 8 kN, axial load Fa kN, design life LD10ringrotation factor V12 and eliability R 0.9a NOTE: This is a mult-part question. Once an answer is submitted, you will be unable to return to this part. the application 25 poimts Assuming that the values taken...
Cene clutch Figure (4) Motor 04: Figure (4) shows a simple single-reduction bevel gears pair. Power...
Cene clutch Figure (4) Motor 04: Figure (4) shows a simple single-reduction bevel gears pair. Power is received from the motor through a flange coupling to the gearbox. Cone clutch is used to connect or disconnect the motion comes from the motor by the action of the helical spring. Requirements: 1. Power of motor if it has speed of 2000 rpm. 2. If the basic dynamic rating of Deep-groove ball bearing at C is (C = 3.94 kN), find the...
Need step by step solution please The figure shown is a geared countershaft with an overhanging...
Need step by step solution please
The figure shown is a geared countershaft with an overhanging pinion at C. Select an angular- contact ball bearing from Table 11-2 for mounting at O and an 02-series cylindrical rolleor bearing from Table 11-3 for mounting at B. The force on gear A is FA 5 600 lbf, and the shaft is to run at a speed of 420 rovimin. Solution of the statics problem gives force of bearings against the shaft at...
mechanical Desgin 2
11 - 20: A single-row deep-groove ball bearing with a 65-mm bore (see Tables 11-1 for specifications) is loaded with a 3-KN axial load and a 7-KN radial load. The outer ring rotates at 500 rev/min. (a) Determine the equivalent radial load that will be experienced by this particular bearing. (b) Determine whether this bearing should be expected to carry this load with a 95 percent reliability for 10 kh.
Table 11-2 Dimensions and Load Ratings for Single-Row 02-Series Deep-Groove and Angular-Contact Ball Bearings Load Ratings, kN Fillet Shoulder Width, Radius, Deep Groove Angular Contact Bore, OD, Diameter, mm ds C10 с. Сто Co mm mm mm mm 10 30 9 0.6 12.5 27 5.07 2.24 4.94 2.12 12 32 10 0.6 28 6.89 3.10 7.02 3.05 14.5 15 35 11 0.6 17.5 31 7.80 3.55 8.06 3.65 17 40 12 0.6 19.5 34 9.56 4.50 9.95 4.75 20 47...
HW Bearings 4 Required information A 02-series single-row deep-groove ball bearing is to be selected from Table 11-2 for the application conditions specified in the lable. Assume Table 11-1 is applicable if neetded. The value of radial oad F-10 kN, axial led Fa-5 kN, design life 12 kh and 300 revimin, ring rotation factor V-1.0, and reliabilty Ro-0.98 ら:5kN- actor V 25 NOTE. This is a multi-part question Once an answer is suibrnited, you waill be unable to return t...
A Bearing A is a deep groove type and bearing B is an angular contact sölid shaft is mounted on two Single-Row 02-Seri es Ball bearings The radial loads are Fr2472N, FR 3422N, axial load is Pa and the minimum static rating is 11000N. The design characteristics are speed of 500rpm, d application factor is 1.25,xo 0.02,-4.459, b- 1.483,a reliability of each bearing is to be at least 95.0%. The inner rings sign life of 10000hr, manufacturer rated life 10....
5. Bearing life prediction. (20 points) A 02-series Score: with a 50 mm bore (sce Tables 11-1 and 11-2 for specifications) is loaded with a 2.6 kN radial load and a 4.17 KN axial load. The inner ring rotates at 1450 rev/min. The application es single-row angular contact b factor is a,1.3. C1) Determine the equivalent radial load that will be experienced by this particular bearing. (2) Determine the predicted life (in hours) that this bearing could be _expectedtogvein this...
A 02-series angular contact ball bearing with a 10-mm bore is
loaded with a 0.3604 kN axial load and 100 kN radial load. The
inner ring rotates at 8000 rev/min and working 2000-hour service.
For Rd = 93% and af = 1.
(a) Determine the equivalent radial load that will be
experienced by the bearing.
(b) Consider a rating rated life of 10^6 revolutions find C10
load experienced by bearing and calculate the factor of safety in
carrying the load...
) Given: You have to use a series 02 deep grove ball bearing with a C10 rating of 30.7KN and a catalog life rating of 106 cycles. The inner ring rotates and the reliability is 90%. You want the bearing to last 4000hrs at 1200RPM. What is the Fo (desgin rating). Given: You have to use a standard series 02 deep groove ball bearing. Your design radial force is 650Lb and your design life is 25Khrs. The torque being transmitted...
HW Bearlngs Required information A 02-series single-row deeo-groove oall bearing is to oe selected trom lable 11-2 tor t conditions specited in the tableme Talble 11-1 is applicable if needed The value of raa oad Fr 8 kN, axial load Fa kN, design life LD10ringrotation factor V12 and eliability R 0.9a NOTE: This is a mult-part question. Once an answer is submitted, you will be unable to return to this part. the application 25 poimts Assuming that the values taken...
Cene clutch Figure (4) Motor 04: Figure (4) shows a simple single-reduction bevel gears pair. Power is received from the motor through a flange coupling to the gearbox. Cone clutch is used to connect or disconnect the motion comes from the motor by the action of the helical spring. Requirements: 1. Power of motor if it has speed of 2000 rpm. 2. If the basic dynamic rating of Deep-groove ball bearing at C is (C = 3.94 kN), find the...
Need step by step solution please
The figure shown is a geared countershaft with an overhanging pinion at C. Select an angular- contact ball bearing from Table 11-2 for mounting at O and an 02-series cylindrical rolleor bearing from Table 11-3 for mounting at B. The force on gear A is FA 5 600 lbf, and the shaft is to run at a speed of 420 rovimin. Solution of the statics problem gives force of bearings against the shaft at...
Most questions answered within 3 hours.
-
What's the streaming business's problem on the
horizon?
asked 40 minutes ago -
I need help with writing the conclusion for this online lab
report
Abstract
By testing the...
asked 53 minutes ago -
For the reaction 1N2+3H2-----> 2NH3, would the reaction rate
trend be: delta[NH3]/ delta t = -2...
asked 1 hour ago -
Within your current/past organization, identify a problem/issue
and format a design to address same. You may...
asked 1 hour ago -
A sock stuck to the side of a clothes-dryer barrel has a
centripetal acceleration of 24...
asked 2 hours ago -
A perfect gas undergoes an isentropic process such that its
volume doubles. If the ratio of...
asked 2 hours ago -
list the elements in groups 3A to 6A in the same order as in the
periodic...
asked 2 hours ago -
Estimating effect size. Peng and Chen (2014)
evaluated effect size estimates for various tests. In their...
asked 2 hours ago -
Write a script in MySQL that creates and calls a stored
procedure name test. This procedure...
asked 2 hours ago -
If we test the following: H0: μ = 17
vs. H1: μ ≠ 17 and the...
asked 3 hours ago -
in the past year TVG had revenues of 3 million, cost
of goods sold of $25...
asked 3 hours ago -
4) In a polypeptide, which bond cannot rotate because of its
partial double bond character?
The...
asked 3 hours ago