question 9 (a) 9 Design interior one-way slabs for the situations shown. Concrete weight 150 lb/ft3,...
Design interior one-way slab for the situation shown. Concrete weight = 150 lb/ft^3 f_y= 60,000 psi, f_c= 4,000 psi. Do not use the ACI Code’s minimum thickness for deflections. Assume: h= 7.5 in, b= 12 in, d= h-0.75-(0.25) steel percentages are given on the figures. The only dead load is the weight of the slab WL150 psf im -24 ft WL150 psf im -24 ft
Design an interior one-way slab for the figure and load shown below. Given: fc = 4000 psi, fy 60,000 psi The only dead load is the weight of the slab Do not use the ACI Code's minimum thickness for deflection Table 7.3.II Steel percentage p 0.0143 is given in the figure. Finally sketch the slab and show the approximate bar location ρ=0.0143 24
Assume normal concrete weight (wc = 143 lb/ft) with specified compressive strength fc = 4,000 psi, and steel Grade 60 (fy = 60,000 psi). For design loads assume dead load wd = 30 lb/ft? (excluding self-weight) and live load we = 100 lb/ft. Finally assume that the steel percentage ratio is equal to p= 0.18fc/fy. Design an interior one-way simply supported slab with a 15 ft span using the above assumptions. Show sketches of one-way slab cross section, including reinforcing...
Problem 3 Assume normal concrete weight (wc = 143 lb/ft) with specified compressive strength fc = 4,000 psi, and steel Grade 60 (fy = 60,000 psi). For design loads assume dead load wd = 30 lb/ft? (excluding self-weight) and live load wų = 100 lb/ft. Finally assume that the steel percentage ratio is equal to p= 0.18fc'/fy. Design an interior one-way simply supported slab with a 15 ft span using the above assumptions. Show sketches of one-way slab cross section,...
Example CVEG 4303: Reinforced Concrete I One-Way Slabs A 5" thick concrete slab is reinforced for tension with #4 bars spaced at 7". The effective depth is 4" Grade 60 bars and 8,ooo psi concrete will be used. 1.) Determine the design bending strength (фМп) of the slab. 2.) Check that ACI requirements for rebar strain, rebar spacing, and minimum reinforcement are met (ACI 7.3.3.1, ACI 24.3.2, and ACI 7.6.1.1 respectively). Note: Do not need to check temperature and shrinkage...
B. Design an interior one-way slab considering the given loading. The weight of the slab is not included in the given loading. Include a reasonable estimate for the slab weight. Use Pmax = 0.18 fc/fy. Choose a es not exceed twice the thickness of the slab. Show sketch of cross section including bars sizes and spacing. Assume normal weight concrete that weighs 150 pcf, fy = 60,000 psi, fc = 4,000 psi. W. = 100 psf
A one-way solid concrete slab is to be used for a simple span of 16 ft. In addition to its own weight, the slab carries a superimposed dead load of 20 psf and a live load of 90 psf. Design the slab for minimum thickness if ƒy is 40 ksi, and ƒ’c is 3 ksi 9 in 8 in 6 in 7.6 in
Name: Date: 2. (+35) Design a typical interior tension-reinforced T-beam to resist positive moment. Beam dimension is given. The service loads are 150 psf dead load (doesn't include the beam weight) and 350 psf live load. The beam is on a simple span of 20 ft. Use f:=4000 psi for strength concrete and fy=60000 psi for steel reinforcement. 8-0* (typ.)
. Design a reinforced concrete continuous one-way floor system shown below. All dimensions provided are from center-to-center, unless specified otherwise. Given: fC 4,000 psi, normal-weight concrete,f 60,000 psi L 120 psf, D 40 psf+ Self weight Use minimum b 12 in. for beams and girders (You can increase bw if needed) (a) Design a continuous one-way slab over two spans Assume ends integral with the support (spandrel) for moment calculations using the ACI Design Code.
2-You are given the task of designing a simply supported one-way slab, with a 13 feet span. The slab supports a live load of 200 psf. Use fc=3,000 psi, fy=60,000 psi. Provide a sketch of your design. 1 - Provide three (3) provisions about bar choosing/placing in concrete slabs, which you would need to consider as a structural engineer. Discuss the rationale behind each item. 2- You are given the task of designing a simply supported one-way slab, with a...