The cantilever bar in the figure is made from AISI 1018 CD
steel and is statically loaded with Fy = 800 N, and Fx = Fz = 0.
The fillet radius at the wall is 2 mm with theoretical stress
concentrations of 1.5 for bending, 1.2 for axial, and 2.1 for
torsion.Sut = 440 MPa = 64 kpsi, Sy = 370 MPa = 54 kpsi. Analyze the
stress situation in rod AB by obtaining the following
information.a) Determine the precise...
B) A 10-mm ID steel tube carries liquid at 7 MPa. The pressure varies periodically from zero to Maximum. The steel has Sut=400 MPa. Tubing axial stress is zero; the tubing finish is machined; reliability is 99.999%; and the tubing is at room temperature. The maximum principal stresses are: olmaxa = 38.82 MPa ; o2maxa = 0 MPa; 63maxa =. 7.00 MPa Determine the infinite-life fatigue safety factor for the Wall if its thickness is 1 mm. (20) Problem 2:
An overhanging steel beam is used to carry a uniformly distributed load over a 2-metre length as shown. The yield stress of steel is ơyield-350 MPa. Check if the cross section of the beam at section a-a is safe against yielding, (a) using the maximum distortion energy criterion (Von Mises criterion) (b) using the maximum shear stress criterion (Tresca) 15 mm w-12 kN/m 15 mm 120 mm 2000 mm 15 mm 3000 mm 3000 mm 6000 mm 60 mm
An...
Question A-36 steel pipe with an outer diameter of 100 mm and an inner diameter of 80 mm subjected to loadings shown in Figure 1. The pipe is rigidly fixed at B and P = 150 kN. Given the yield stress, Oy=250 MPa and factor of safety, F.S. = 1.5 is used against yielding on this entire pipe. (a) For the stress state at the surface, construct the Mohr circle and determine: (1) the total stresses at surface of the...
Question A-36 steel pipe with an outer diameter of 100 mm and an inner diameter of 80 mm subjected to loadings shown in Figure 1. The pipe is rigidly fixed at B and P - 150 kN. Given the yield stress, Oy -250 MPa and factor of safety, F.S. - 1.5 is used against yielding on this entire pipe. (a) For the stress state at the surface, construct the Mohr circle and determine: (1) the total stresses at surface of...
Question 3 For the simply supported steel beam with cross section and loading shown (see Figure 3a), knowing that uniformly distributed load w=60 kN/m, Young modulus E = 200 GPa, and yield stress Cyield=200 MPa (in both tension and compression). ул 15 mm w=60 kN/m ... 1 B A 15 mm + 300 mm IC - i 2.5m 1 1 15 mm 7.5m 1 150 mm Figure 3a (a) Check if: the beam is safe with respect to yielding (using...
(3pts): The truss is constructed of A36 steel (E -2 a cross-sectional area of 250 mm2. Answer the following s 300 Clbe wna -250 MES, AI 00 G Pa and O, 250 MPa). All truss members have (a) Determine the normal stress and strain in member CD. (b) The support at joint D uses a pin placed in double shear. The pin diameter is 20 mm Determine the average shear stress acting in the pin. 50 kN 50 kN 25...
Q-1. You are testing a circular beam of two metals, 1045 steel and 2014-T6 aluminum, in a rotating-cantilever beam fatigue test. If you need to choose one of these metals so that you can essentially design a part made of that metal, and subject the part to a repetitive stress- amplitude without ever failing due to fatigue, which one would you choose. (See the attached figure) 700 600 Ti-5Al-2.5Sn titanium alloy 4340 steel 500 400 Maximum stress, S (MPa) 1045...
Example: 1.2 A wrench is made of steel (E=210 GPa, v=0.3) with elastic constants of strain components for a state of plane stress at a critical point in the structure are calculated as 6, 50 x 10 = -75x10* 1 = 150 x 10"rad. a) Determine the complete strain and stress matrices in this state of stress, b) Determine the in-plane state of stress with rotating current coordinate system an angle of 45 degrees clockwise by applying either the transformation...
The figure shows a transmission shaft. The steel solid shaft is 200 mm long between self-aligning bearings at A and B. Belt forces in the same horizontal direction) are applied to a 120-mm diameter sheave at C. The left end of the shaft is connected to an electric motor attached to a clutch by means of a flexible coupling. Nothing is attached to the right end (it is free). Assuming the shaft has a constant diameter, d. (a) Perform the...