Homework Answers
Add Answer to:
Q2: One side of a petrol drill pipe, as shown in the figure, has been lifted...
Question-4.125 points A drillstring made up of steel drill pipe, drilil collar and a drill bit...
Question-4.125 points A drillstring made up of steel drill pipe, drilil collar and a drill bit is hanging from the hook (offbottom) in a well, as shown in the diagram below (a) Determine the tensile stress at A (at the top cross-section of drill pipe), C (at bottom cross-section 20 points of drill pipe), and B (at bottom cross-section of drill collar). [2x10 section A? Explain. [5 points] Data: Weight of the bit-500 N (b) If the yield strength (ay)...
The JT100 horizontal directional drilling machine applies 220 hp and rotates drill pipe at 100 rp...
The JT100 horizontal directional drilling machine applies 220 hp and rotates drill pipe at 100 rpm. During the drilling process, a drill pipe is subjected to the following axial and bending loads 30.0 Axial load, P, of 100 kips 0.70 ft-kips bending load, M, in the y-z plane at 30 degrees from the vertical axis The drill pipe, which is made of AISI 4130 steel, has the following dimensions and material properties (Ref. MIL-HDBK-5J, Table 2.3.1.0(c1)) » Length, L 177-in...
The hollow steel construction auger in Figure 4 has an outer diameter d2 = 140 mm...
The hollow steel construction auger in Figure 4 has an outer diameter d2 = 140 mm and thickness of t = 8 mm. The steel has a shear modulus of elasticity E = 200 GPa and v = 0.3. For an applied torque of 35 kN m, determine the following quantities: a) Shear stress at the mid-center of the thickness t of the shaft. [2] b) Shear stress on the outer surface. [1] c) Shear stress in the inner surface,...
For the pipe system below, we assume the cross-section at A is subject to the resultant forces P ...
For the pipe system below, we assume the cross-section at A is subject to the resultant forces P 339 N and Py 448 N. The pipe gauge pressure is given by p 6 b 212 mm and c 263 mm. The circular cross-section has outer diameter do 95 mm and inner diameter d 55 mm 623 kPa. Use the dimensions a 318 mm, Py Determine the state of stress at point K: evaluate the magnitude of the stresses and draw...
strength of material engineering of mechanical please solve this question 50 km 03: The pipe shown...
strength of material
engineering of mechanical
please solve this question
50 km 03: The pipe shown in figure below has an inner diameter of 100 mm and an outer diameter of 120 mm is subjected to the loadings shown. Determine the principal stress and the maximum in-plane shear stress that is developed af section B. 20 MARK 10 N 30 KN
Question 5 16 pts The steel pipe AB has a 72-mm outer diameter and a 5-mm...
Question 5 16 pts The steel pipe AB has a 72-mm outer diameter and a 5-mm wall thickness. Knowing that the arm CDE is rigidly attached to the pipe, determine the normal and shearing stresses at point H on the outer surface. The properties at the cross section at H include: A 1052.4 mm2,J 1,187,700 mm4, 1 593,840 mm4, and QNA 11,243 mm3 3 kN 9 kN 120 mm 150 mm 120 mm a.) Normal stress at H: b.) Shear...
The cantilever beam shown in the figure is subjected to a concentrated load at point B....
The cantilever beam shown in the figure is subjected to a concentrated load at point B. The stresses acting at point H on the beam are to be determined. H Cross section For this analysis, use the following values: Beam and Load. a = 1.75 m b=0.30 m @= 60 degrees P = 25 KN Cross-sectional Dimensions d=250 mm bp = 125 mm ty=7 mm tw = 7 mm C= 30 mm (Note: The load P applied at Bacts in...
The cantilever beam shown in the figure is subjected to a concentrated load at point B....
The cantilever beam shown in the figure is subjected to a concentrated load at point B. The stresses acting at point Hon the beam are to be determined Ques! Text- Quest Text Ent T Quest Text End Cross section Viewir Text-Ent For this analysis, use the following values Beam and Load. Questi Muitstep a. 1.75 m b-0.30 m 0.63 degrees P.49 KN Questid Text Entry Questio Text Entry Cross-sectional Dimensions d - 275 mm by - 150 mm - 13...
1. A solid steel bar of diameter d; = 25.0 mm is enclosed by a steel...
1. A solid steel bar of diameter d; = 25.0 mm is enclosed by a steel tube of outer diameter d3 = 37.5 mm and inner diameter d2 = 30.0 mm (see figure). Both bar and tube are held rigidly by a support at end A and joined securely to a rigid plate at end B. The composite bar has a length L = 600 mm and is twisted Tube by a torque T = 400 N-m acting on the...
1.5-7 A hollow, brass circular pipe ABC (oce figure supports a load P, 118 kN acting at the top A...
please help ASAP
1.5-7 A hollow, brass circular pipe ABC (oce figure supports a load P, 118 kN acting at the top A second load P -98 kN is uaiformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the pipe are 31 mm ,,-12 mm, dae" 57 mm, and tac· 9 mm, respectively. The modulus of clasticity is 96 GPa. When both loads are fully applied, the wall thickness of...
Question-4.125 points A drillstring made up of steel drill pipe, drilil collar and a drill bit is hanging from the hook (offbottom) in a well, as shown in the diagram below (a) Determine the tensile stress at A (at the top cross-section of drill pipe), C (at bottom cross-section 20 points of drill pipe), and B (at bottom cross-section of drill collar). [2x10 section A? Explain. [5 points] Data: Weight of the bit-500 N (b) If the yield strength (ay)...
The JT100 horizontal directional drilling machine applies 220 hp and rotates drill pipe at 100 rpm. During the drilling process, a drill pipe is subjected to the following axial and bending loads 30.0 Axial load, P, of 100 kips 0.70 ft-kips bending load, M, in the y-z plane at 30 degrees from the vertical axis The drill pipe, which is made of AISI 4130 steel, has the following dimensions and material properties (Ref. MIL-HDBK-5J, Table 2.3.1.0(c1)) » Length, L 177-in...
The hollow steel construction auger in Figure 4 has an outer diameter d2 = 140 mm and thickness of t = 8 mm. The steel has a shear modulus of elasticity E = 200 GPa and v = 0.3. For an applied torque of 35 kN m, determine the following quantities: a) Shear stress at the mid-center of the thickness t of the shaft. [2] b) Shear stress on the outer surface. [1] c) Shear stress in the inner surface,...
For the pipe system below, we assume the cross-section at A is subject to the resultant forces P 339 N and Py 448 N. The pipe gauge pressure is given by p 6 b 212 mm and c 263 mm. The circular cross-section has outer diameter do 95 mm and inner diameter d 55 mm 623 kPa. Use the dimensions a 318 mm, Py Determine the state of stress at point K: evaluate the magnitude of the stresses and draw...
strength of material
engineering of mechanical
please solve this question
50 km 03: The pipe shown in figure below has an inner diameter of 100 mm and an outer diameter of 120 mm is subjected to the loadings shown. Determine the principal stress and the maximum in-plane shear stress that is developed af section B. 20 MARK 10 N 30 KN
Question 5 16 pts The steel pipe AB has a 72-mm outer diameter and a 5-mm wall thickness. Knowing that the arm CDE is rigidly attached to the pipe, determine the normal and shearing stresses at point H on the outer surface. The properties at the cross section at H include: A 1052.4 mm2,J 1,187,700 mm4, 1 593,840 mm4, and QNA 11,243 mm3 3 kN 9 kN 120 mm 150 mm 120 mm a.) Normal stress at H: b.) Shear...
The cantilever beam shown in the figure is subjected to a concentrated load at point B. The stresses acting at point H on the beam are to be determined. H Cross section For this analysis, use the following values: Beam and Load. a = 1.75 m b=0.30 m @= 60 degrees P = 25 KN Cross-sectional Dimensions d=250 mm bp = 125 mm ty=7 mm tw = 7 mm C= 30 mm (Note: The load P applied at Bacts in...
The cantilever beam shown in the figure is subjected to a concentrated load at point B. The stresses acting at point Hon the beam are to be determined Ques! Text- Quest Text Ent T Quest Text End Cross section Viewir Text-Ent For this analysis, use the following values Beam and Load. Questi Muitstep a. 1.75 m b-0.30 m 0.63 degrees P.49 KN Questid Text Entry Questio Text Entry Cross-sectional Dimensions d - 275 mm by - 150 mm - 13...
1. A solid steel bar of diameter d; = 25.0 mm is enclosed by a steel tube of outer diameter d3 = 37.5 mm and inner diameter d2 = 30.0 mm (see figure). Both bar and tube are held rigidly by a support at end A and joined securely to a rigid plate at end B. The composite bar has a length L = 600 mm and is twisted Tube by a torque T = 400 N-m acting on the...
please help ASAP
1.5-7 A hollow, brass circular pipe ABC (oce figure supports a load P, 118 kN acting at the top A second load P -98 kN is uaiformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the pipe are 31 mm ,,-12 mm, dae" 57 mm, and tac· 9 mm, respectively. The modulus of clasticity is 96 GPa. When both loads are fully applied, the wall thickness of...
Most questions answered within 3 hours.
-
What specific indicators can point to lack of progress for
African Americans in American society?
asked 3 minutes ago -
1-The Electrons in a beam are moving at 2.7×108 m/s in an
electric field of 15000...
asked 19 minutes ago -
A gas tank is a vertical cylinder. It has a radius of 1m, a
height of...
asked 45 minutes ago -
Accent Software faces the following conditions. All of these
support Accent’s use of a market-penetration pricing...
asked 1 hour ago -
A mathematically inclined friend emails you the following
instructions: "Meet me in the cafeteria the first...
asked 1 hour ago -
A monopoly sells in two countries . The demand curves in the two
countries are p1...
asked 2 hours ago -
A .15kg rubber ball is bounced off a wall. Before hitting the
wall, the ball moves...
asked 3 hours ago -
A manufacturing company preparing to build a new plant is
considering three potential locations for it....
asked 3 hours ago -
B. If compound Y has approximately the same values of solubility
in toluene as compound X,...
asked 4 hours ago -
Oscar Inc. has inventory in Japan valued at 39,051,000 Yen one
year ago. One year ago...
asked 4 hours ago -
If Canada suffered from "fundamental disequilibrium," and its
government choose not to devalue its currency, a...
asked 4 hours ago -
4. How many input & output Key Value Pairs are passed into,
and emitted out of...
asked 4 hours ago