i) Determine the gear ratio and transfer function for the gear train between the driver gear...

Question

Question

i) Determine the gear ratio and transfer function for the gear train between the driver gear (gear 1) and the driven gear (ge

Answer 1

Answer #1

F dear olauiny dear no dedh olia gear tead h 10x15 40x30 Spea daion Ny Ta-45 10X15 T To THn 1B 45x 60 Pucreoses Her, T teedh

Answer 2

Similar Homework Help Questions

estion- a) Find the speed ratio of the gear train shown in figure. What will be...

estion- a) Find the speed ratio of the gear train shown in figure. What will be the direction of gear 7 b) Determine pitch line velocity (v r.w) of gear &, provided for gear 6 Imodule (D/T) 5mm e) If double the speed ratio (as calculated in a) is required with a simple gear train (having only two gears) number of teeth on driven gear, provided input gear has 20 teeth. IST IST 25T 33T I8T An epicyclic gear train...
Show all work. A compound reverted gear train will be used to decrease speed with a...

Show all work. A compound reverted gear train will be used to decrease speed with a ratio of 36 to 1. In the figure below, the input shaft drives gear 5, and the output shaft is driven by gear 2. Use spur gears with a 20 degree pressure angle and a diametral pitch of 5 teeth / in. a) Specify the appropriate numbers of teeth for both gear sets to minimize the gearbox size, while also avoiding gear tooth interference....
2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5...

2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5 hp electric motor. All of the gears have a diametral pitch of 8 teeth per inch. i) What is the ratio of output torque (Gear 4) to input torque (Gear 1)? j) Is it a coincidence that it is the same as the answer in 1 An input shaft drives Gear 1 with 20 teeth at 1800 rpm which mates with the 80-tooth Gear...

In the gear train shown below, the pinion 2 is the driver, and gear 5 is...

In the gear train shown below, the pinion 2 is the driver, and gear 5 is the output gear. All gears are spur gears has a module of 2.5mm and pressure angle of 200. The number of gear teeth are: N2 - 14, N3 - 84, N4 - 14, N5 - 70 teeth. The gear set transmits the power of 1.5KW at a constant angular velocity of XX rev/min. Where XX is the last two digits of your University ID...
UU 7. A planetary gear train is shown in Figure P7. The carrier (link 2) serves...

UU 7. A planetary gear train is shown in Figure P7. The carrier (link 2) serves as the input to the train. The sun (gear 1) serves as the output from the train and has a 1.0-in. pitch diameter with a diametric pitch of 20. Gear 3 has 45 teeth and gear 4 has 20 teeth Gear 5 has 30 teeth and is keyed to the same shaft as gear 4. Gear 5 mates with the ring gear (gear 6),...
[2] (15 PTS) Use the formula method Figure below represents an ingenious gear train in which...

[2] (15 PTS) Use the formula method Figure below represents an ingenious gear train in which the arm is the driver. Determine the speed ratio of output to input for this mechanism. Take counter-clockwise viewed from left as positive. The sun gear S2 is fixed. Pl (101 teeth) P2 (102 teeth) Arm S2 (99 teeth) Output Input Sl (100 teeth) P1 P2

2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5...

2. Gear dynamics. The gear train above is driven on the input shaft with a 0.5 hp electric motor. All of the gears have a diametral pitch of 8 teeth per inch. a) What are the diameters of Gears 1, 2, 3, and 4? b) What is the pitch-line velocity of Gear 1, in ft/min? c) Is the pitch-line velocity of Gear 2 the same as Gear 1? d) What is the pitch-line velocity of Gear 3 (and, therefore, Gear...
i want to get part c,d The figure below is a gear-train mechanical system driven by...

i want to get part c,d The figure below is a gear-train mechanical system driven by a prescribed motion in the form of an angular displacement y(t). The motion is caused by an applied torque T(t) generated by a motor. The mass moment of inertias of the motor and the driving gear are J and J, respectively, whereas the mass moment of inertias of the load and the driven gear are J, and J2, respectively. The radii and angular displacements...
A shaft that carries gear 2 and 3 is supported by two bearings at B and D. Gear 4 is the driver g...

A shaft that carries gear 2 and 3 is supported by two bearings at B and D. Gear 4 is the driver gear and gear 1 is the driven gear. All gears have 20° pressure angle with diametral pitch equal to 3. The driver has N 30 teeth and transmit 75 HP at 300 rpm. The numbers of teeth of other gears are: Ni-24; N2 30; N 48 All gears are steel with Poisson's ratio of 9 .028. Use AGMA...

Determine the ratio between the sun gear and arm given the following: Ring gear 80 teeth,...

Determine the ratio between the sun gear and arm given the following: Ring gear 80 teeth, sun gear 40 teeth, planet gear 20 teeth Ring gear is stationary Wring=0 Arm Warm=1 Planet Ring gear 801 Output Ring gear 4 Arm Sun gear Planet 206 3 Arm Sun 400 Arm 2 Input 1 Input 2 Bearing