Assume that v.is a I ktz. 10 V oin resulting at v, (5 pts) and (iü)...
Please note that D4 is the one that was destroyed not D1. Please I posted this but they answer it differently QUESTION (2) Due to an abnormal operating condition, Diode D4 in this full-wave rectifier circuit was suddenly destroyed, and stopped Vconducting in both forward and reverse directions (i.e. open circuit) C- R Assume that all other diodes are ideal with zero forward voltage drop and that the time constant RC- 5 ms. stt) 10V For a 1 kHz triangular...
Shirt /10 pts 2 (10 pts) Half-wave rectifier circuit (Multiple Choice) For the rectifier circuit below, let the input be a sine wave with a value of 120 Vrms and assume a constant voltage drop model of 0.7 V p D Select a suitable value for R so that the peak diode current does not exceed 50 mA a 2400 0 32250 A. B. 3000 0 C. 3380 0 D the diode? b. What is the greatest reverse voltage that...
QUESTION 5 (15 points) a. You have a power supply which is a full-wave rectifier with a capacitor filter. It operates from the mains and provides an output of Voc-20 V with 20% ripple, when the load current is 2 A Calculate the maximum and minimum values of the output waveform of this power supply. b. Now you will design a series voltage regulator between the power supply described in part (a) and an electronic device operating at 12 VDC...
9) What is the minimum output voltage for this clamping circuit? +10 h -10 U 1.0V I Ş A) - 11 V B)-1V C) +21 V D) +1 V 10) 10) What are the minimum and maximum values of current flowing in the variable load resistor while the diode is operating in the Zener region? The zener voltage is 10 V. 1000 OW Vin= 50V Load A) & mA and 35 mA B) Need to know the load resistance to...
02 +Vo D3 Rgare 18 Circuit for Problem 1 Analysis 1. Copy the circuit of Figure 1.8 and sketch the ow of pesitive curment throughout the entire circuit for o>0. Repeat for n ce 2. Plot two periods of nlt) and s) for each of the thee input wave shown in Figune 17 on page 37 fom output t (a) Feak value, and b) Eflective DC value, also known as RMS value NotTE These and are therefore optional 4. Determine...
I need help with #5. Thank you. 4] For the three circuits below sketch the output voltage VO for an input signal Vi-4sin(2 t). Assume a 0 V diode forward voltage. Vo 3.0 V 5] Redo problem 4, but now using a square wave with an amplitude of 10 V as input voltage. Assume that the diode forward drop is 0.4 V Exercise 5 from the HW, 1st circuit: what is the value of 10 at time 0.75 seconds? 10...
A common source amplifier circuit based on a single n-channel MOSFET is shown in Figure 4b. Assume that the transconductance gm-60 mS (equivalent to mA/ V) and drain source resistance, os, is so large it may be neglected. 0) Calculate the open circuit voltage gain Av Yout/ Vis. i) The amplifier has a load of 10 k2. Determine the current gain Va. = 12 V 150k 4k3 Vout Vin 200k GND = 0 V Figure 4b a) State the name...
VDD 1.8 V VTOn0.373 V VTOp0.395 V 0.09 um 0.580 vo.5 kp 94.3 HA/V2 VAn' - 15 V/um Vae' = 10 V/μm p 0.576 Vo.5 0.3 V for both transistors 1, (20 pts total) Consider the voltage transfer characteristic shown in the figure with VDD = 1.8 V. a) (6pts) Is this a CMOS inverter? b) (7pts) What are VoH, VoL, ViL, VIH, NMH, NML, and VM on the graph? Use the definitions from the textbook. c) (7pts) What are...