Find the center of gravity from the left end of the handle for the hammer shown noting that the handle is made of wood and runs all the way through the 2" dia head of the hammer. The head of the hammer is made of a steel column between two steel spheres. Weight of wood is 40 Ib/ft^3.
Find the center of gravity from the left end of the handle for the hammer shown...
Solve ay four ME 246 Q.i A container of weight W - 1165 N is supported by threecables 530 mm as shown. Determine the tension in each cable. 600 mm The uniforma steel boom in Fit 22a weighs soo ib. It is supported by two cabks CE uai CD. and a ball-and socket joint at A. The cable supporting the 1000-6 dasses over a small pulley at B. Find the tension in cable CE and in cable 1 4 rt...
A block slides from rest, along a track with an elevated left
end, a flat central part, into a relaxed spring, as shown in the
figure. The curved portion of the track is frictionless, as well as
the first portion of the flat part of L = 10 cm. The coefficient of
kinetic friction between the block and the only rough part, D = 10
cm, is given by k = 0.20. Let the initial height of the block be...
One end of a meter stick is pinned to a table, so the stick can rotate freely in a plane parallel to the tabletop. Two forces, both parallel to the tabletop, are applied to the stick in such a way that the net torque is zero. The first force has a magnitude of 2.00 N and is applied perpendicular to the length of the stick at the free end. The second force has a magnitude of 6.00 N and acts...
Please answer question 4 thank you. Results from problem 3 are
shown above
Reinforced Concrete
3. (40 pts) Analyze the following statically determinate frame by hand and clearly draw the shear force, axial force, and bending moment diagrams indicating relevant (maximum and minimum) values for each of the following load cases: a) Uniform dead load (qo) applied on the beam – must add beam self-weight (concrete) to this value. b) Uniform live load (q) applied on the beam. c) Horizontal...
Question (20 marks Analysis only required Water at 15°C is discharged freely to atmosphere from a reservoir at 18 L/s through two horizontal pipes in series and a pump-motor assembly in between as shown in figure below. First pipe-A is made of cast Iron and is 20m in length with a 60mm dia. The second pipe-B is 35 m in length, has a 40 mm diameter with friction factor 0.0331. The pipe entrance from reservoir is sharp edged. Neglect any...
Please answer all parts of the questions and please
try making them clear and easy to understand.
CONCEPTUAL QUESTIONS: (Total Points 10, 1 points each question) 1- A plate is supported by a bal-and-socket joint at A, a roller joint at B, and a cable at C. How many unknown support reactions are there in this problem? 300 N 400 N i m A) Four forces and two moments B) Six forces C) Five forces D) Four forces and one...
1. KINEMATICS: Kickoff During kickoff for the Oakland Raiders, Sebastian Janikowski's powerful left leg launches the ball from the 30-yard line with the initial velocity of 30 m/s. a. Assuming no air resistance, can the ball reach the end of the field, i.e. travel at least 80 yards (73 m), resulting in a touch-back? Please explain (a yes or no answer is not sufficient) b. Assuming Mr. Janikowski chose the best possible angle for the kick, how long is the...
please solve with details
Question#1140Marksl The shaft shown in the figure is rotating at 650 rpm and it receives 5592.75 W through a flexible coupling at its right end. The power is delivered to an adjacent shaft through a single helical gear B having a normal pressure angle of 20° and a helix angle of 15o. The pitch diameter for the gear is 105.1814 mm (4.141 in). A spacer is used to position the gear relative to bearing C. The...
auge Steel Framing Details 1. Complete all light g auge steel componente ir the following wall section, including floor joists, wall studs, roof rafters, and required clips angles, stiffeners, and fasteners. Label all components. Roof sheathing Wall sheathing 。 Interior wallboard Subflooring Foundation 103 Scale: l square =2" (50 mm) Name: necessity of cutting holes in m on the construction ste 12.11. 12.15). Thack etions a sed for top and bottom plates, e construction, shemperature that col tural shapes. Prers...
IB math studies
1. Ten students were asked for their average grade at the end of their last year of high school and their average grade at the end of their last year at university. The results were put into a table as follows: Student High School grade, University grade, y 90 3.2 2.6 75 80 3.0 70 95 3.8 85 90 3.8 2.8 70 95 85 3.0 3.5 10 Total 835 30.4 (a) Given that s, 8.96, sy-0.610 and...