Question

a A horizontal bracket ABC consists of two perpendicular arms AB and BC as shown in the figure. Amm AB has a solid circular c

0 0
Add a comment Improve this question Transcribed image text
Answer #1

TE INDUSTRIES Taro =8072 20 P, 22:07 kW XD 9 bom 7 1 1 228 kNm B 7.6M 6,20€ 6.808 t due to 0.808nm at point p 16x0 1806X0 = 1

Add a comment
Know the answer?
Add Answer to:
a A horizontal bracket ABC consists of two perpendicular arms AB and BC as shown in...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • A horizontal bracket ABC consists of two perpendicular arms AB of a length 0.75 m and...

    A horizontal bracket ABC consists of two perpendicular arms AB of a length 0.75 m and BC of a length 0.5 m. The bracket has a solid, circular cross section with a diameter equal to 65 mm. The bracket is inserted in a frictionless sleeve at A (which is slightly larger in diameter), so it is free to rotate about the z0 axis at A and is supported by a pin at C. Moments are applied at point C M1=...

  • A cantilever beam, with a rectangular cross section, is subjected to loads P, Q and R,...

    A cantilever beam, with a rectangular cross section, is subjected to loads P, Q and R, as illustrated in the figure below. Given, P 100 kN, Q 15 kN and R 10 kN, determine the principal stresses and the maximum in-plane shearing stress at point B. Also, determine the planes on which the principal stresses act, and the planes on which the maximum in-plane shear stress acts. The vertical dimension (depth) of the beam is 120 mm. 40 mmA 2...

  • 3. Figure shows a state of plane stress consists of normal stresses 60 MPa and Ly-40MPa;...

    3. Figure shows a state of plane stress consists of normal stresses 60 MPa and Ly-40MPa; and unknown shear stress, The maximum principal stress was determined to be 104.34 MPa. Using Mohr's cirdle, determine a. the magnitude of the shear stress, b. the principal plane and the minimum principal stress. Then, sketch the element showing all stresses in its proper orientation, c. the maximum shear stress, associated normal stress and the orientation of the element. Then, sketch the element showing...

  • t 4 mm An L-shaped bracket lying in a horizontal plane supports a load P= 600...

    t 4 mm An L-shaped bracket lying in a horizontal plane supports a load P= 600 N (see figure). The bracket has a hollow rectangular cross section with thickness t=4 mm and outer dimensions b = 50 mm and h-90 mm. The centerline lengths of the arms are b-500 mm and b 750 mm. (a) Calculate the normal stress o and the shear stress t at point A, which is located on the top of the bracket at the support...

  • Q3. (30 points) For the state of plane stress shown, Stresses, σ. σ2 (b) the orientation of the p...

    please help me solve this whole mechanical design problem thanks Q3. (30 points) For the state of plane stress shown, Stresses, σ. σ2 (b) the orientation of the principal stresses, s, (c) the maximum in plane shearing stress, Tmar and (d) its orientation, p. (e) the normal stress at the plane of maximum shear stress, (1) sketch of the rotated plane element for the principal stresses and the rotated plane element for maximum shear stress similar to figure 1, below...

  • (a) If the wide-flange beam shown in Figure Q4a is subjected to a shear of V = 23 kN

    (a) If the wide-flange beam shown in Figure Q4a is subjected to a shear of V = 23 kN i. Calculate the moment of inertia of the cross section about the neutral axis.ii. Determine the shear stress on the web at A.(b) The state of stress at a point is shown on the element in Figure Q4b. Determine graphically using Mohr's circle i. The principal stresses. ii. The orientation of the principal planes.iii. The maximum in-plane shear stress and average normal stress at...

  • 3. The states of stress at two points in a loaded beam are represented in Fig....

    3. The states of stress at two points in a loaded beam are represented in Fig. P1.26a. Determine the following for each point: (a) The magnitude of the maximum and minimum principal stresses and the maximum shearing stress; use Mohr's circle. (b) The orientation of the principal and maximum shear planes; use Mohr's circle. (c) Sketch the results on properly oriented elements. [30] SOMPa 60 MPa 100 MPa

  • Q.4 (25 marks) A material is subjected to two mutually perpendicular direct stresses of 300 MPa...

    Q.4 (25 marks) A material is subjected to two mutually perpendicular direct stresses of 300 MPa tensile and 200 MPa compressive, together with a shear stress of 50 MPa, as shown in the figure below. Use the Mohr's circle to determine: A. The principal stresses and their corresponding principal planes, B. The maximum shear stress and the planes of maximum shear stress, also C. Show the principal stresses calculated above on a sketch of the element D. Determine the state...

  • Asap 1. The bracket is made of steel (Young's modulus 200 GPa; Poisson's ratio 0.3). When the force P is applied to the bracket, the gages in the strain rosette at point A have the followi...

    Asap 1. The bracket is made of steel (Young's modulus 200 GPa; Poisson's ratio 0.3). When the force P is applied to the bracket, the gages in the strain rosette at point A have the following readings: E.-60 μ . Ep 135 μ l, and E.-264 μ (a) Determine the shear strain at point A. (b) Determine the orientation of the principal plane, the in-plane principal strains, the maximum in-plane shear strain, and the average in-plane normal strain. Determine the...

  • PROBLEM 2: 40% A 6 kN force is exerted on the frame which has the T cross sectio analyze the states of stress at a section taken at 800 mm from the point of n shown below. It is required to 1. Fo...

    PROBLEM 2: 40% A 6 kN force is exerted on the frame which has the T cross sectio analyze the states of stress at a section taken at 800 mm from the point of n shown below. It is required to 1. For the given T cross section, find the centroid and the area moment of inertia I,. 2. Draw the free body diagram of the free end of the frame and determine the interna loadings at the centroid of...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT