A differential amplifier with a constant current source is shown. The circuit parameters are: Vec =...
(60pts)For the differential amplifier below has the data: 1-1.2 (rnA), Vec-VEE-3 (V), VCM--8 (V), Re-2 and β 100, assume that the BJT have vBE 0.7(V) at ic-1 (mA). Fine the voltage at emitters and at the outputs. If valo) 0.4 sin100nt (mv), vod(t)-? Vcc Rc Rc ici İC2 ei 02 İEI İE2 (60pts)For the differential amplifier below has the data: 1-1.2 (rnA), Vec-VEE-3 (V), VCM--8 (V), Re-2 and β 100, assume that the BJT have vBE 0.7(V) at ic-1 (mA)....
For the differential amplifier shown in Figure (2),assume \(\mathrm{VCC}=12 \mathrm{~V}, \mathrm{VEE}=-12 \mathrm{~V}, \mathrm{Rc}=2 \mathrm{k} \Omega\), and \(\beta=100\) for all transistors.For the current source circuit (Transistor \(\left.Q_{3}\right): R_{1}=4 k \Omega, R_{2}=4 k \Omega, R_{3}=3 \mathrm{k} \Omega\), and \(r_{0}=100 \mathrm{k} \Omega\).a) In differential amplifier circuits, what do "well-matched transistors" mean?b) Why it is important to use well-matched transistors in differential amplifier circuits?c) What are the operating \(Q\) point values \(\left(I_{c Q}\right.\) and \(\left.V_{C Q}\right)\) for the transistors \(Q_{1}\) and \(Q_{2}\) ?d) Draw...
1. (a) Express the differential gain (double side) of the amplifier using TR parameters and Rc. (3pts) (b) Express the differential gain for a single side output. (2pts) (e) Design the Re such that o velve IV when vi5mV and v2+5mV (3pts) (d) Determine the maximum common-mode input voltage (5pts) (e) Determine the differential mode input resistance of the amplifier Beta is 100.(3pts) V+ = 10V R. ci C2 ei 02 2 t )10 = 2 mA V-=-10V 1. (a)...
1. Consider the Common-Emitter BJT amplifier circuit, shown below. VD VOD BJT Parameters: B=99 A/A i=0 RE Co Circuit Parameters: Ca Cc2 = 0 F Car = OF R = 2022 R = 2002 R1 = 25.8 k22 Ry2 = 51.6 ks V = 15 V VEE=0 V Сct Active Mode: Va >0.2 V Vwx=0.7V Ic=B1, Ic=al, 1 R2 3 SRCA a) Find the open-circuit voltage gain, Ave, of this amplifier circuit. Verify your assumptions. b) Compute the input resistance,...
The 1 mA. V, ls -VE -15 15 V, in the following differential amplifier circuit, Vcc parameters are given as β, 100, VBE# 0.7 V, pr-25 mV, K.-100 V. transistor Rc-10 kΩ For: RE-150 Ω Rc Rc REE-200 kΩ a) What is the input differential resistance, Rid b) What is the overall voltage gain vV? You c) What is input common mode resistance, d) What is the worst case common mode gain that appear across the two input terminals? (4...
3.1. For the BJT differential pair configuration shown below, assume the input transistor beta is very large. Then find the differential signal vd = vB1 − vB2 sufficient to cause: 3.2. A differential amplifier resembling that below uses I = 200μA, RC = 10kohm and VCC = 3V. Assume beta is very large 3.4.For the emitter follower in the figure below, given VCC = 15 V, VEE = −15 V, RL = 1 kohm and beta = 100 for all...
WA R3 W Consider the above circuit with indicated parameters and Rs.83.50, R1=20k0, R2=2020, RE1=428.30, RE2-5000, RC=10, RL=5.0kg, B=39, VBE=0.8V, IVAL= 36 V and VT=20mv. For the following questions, do not do your own DC calculations - assume a hypothetical value for IC=4mA. (a) Calculate the input impedance of the amplifier, Ri. Answer: (b) Find the voltage gain vi/vs Answer: (c) Find the voltage gain vo/vi Answer: (b) Find the voltage gain vi/vs Answer: (c) Find the voltage gain vo/vi...
THE STEPS TO DO SO: Design a BJT amplifier based on the specifications provided in the table below. Your design should be insensitive to β variations, and both the input and the output should be AC coupled as in Fig. 1. Supply Voltage, Vcc Load Resistance, RL Transistor's Current Gain, β Relative Variation of lc for VBE-0.7 ± 0.1 V 0-to-Peak Output Swing, Vo Voltage Gain, A Input Resistance, R THD for 5kHz IV (0-to-peak) Sine Wave Output Voltage, V。S5%...
3 (40 pts) MOSFETs in the following active loaded differential amplifier circuit has K 2.5K 250LA/N 0.5V with Vs V-10V Given Va a 0.BV and V Vas Va -0 BV. and assuming saturation mode for aแ devices. answer the questions a (12 pts) In order to establish a bias current of s 200HA calculate the value of R and W/Lratios of matched devices เฉ. ฉ6) matched devices (Q4、Q5), and Q7 b. (8 pts) Calculate the output resistances of matched devices...
pleaseee solve quickly it s urgent!!!!! EEN 311-Electronic Circuits ll (3 eredíįs)-Final Exam fferential amplifier biased with a basic current source rollowing parameters: Voo-Va 12 V. RD 8 ka, and 5. (20 points) Consider the di The circuit has the param Vi - 650 mv, Vov 50 mV, and R 10 k2. The transistors are matched and have: Va=80 V 几 Von Ro &K 오, DGI + VDD REF Q4 THE DE CEER Vss Determine: a) the reference current IREF...