Homework Answers
Add Answer to:
Problem 1 The gas storage tank has a longitudinal welded seam on its cylindrical section. The...
- 3. A propane storage tank is constructed by welding two hemispherical end caps onto a...
- 3. A propane storage tank is constructed by welding two hemispherical end caps onto a cylindrical main body. The cylindrical body is manufactured from a helical welded pipe which has an outside diameter of 750 mm and a wall thickness of 6 mm. The tank is designed to hold gas at an internal gauge pressure of 6 MPa. a) Draw the Mohr’s circle and determine the normal and shear stresses on the weld in the cylindrical main body portion...
A cylindrical pressure vessel of 250 mm mean diameter and 6 mm wall thickness is fabricated...
A cylindrical pressure vessel of 250 mm mean diameter and 6 mm
wall thickness is fabricated from a 1.2 m length of spirally welded
pipe AB as shown. Tank gauge pressure is 4 MPa and centric axial
forces P and P1 of 240 kN act through rigid end plates. Determine:
(a) Net longitudinal and hoop stresses. (b) Normal stress acting
perpendicular to weld and shear stress parallel to weld (show
sketch of Mohr’s circle). (c) Determine the Factor of Safety...
The pressure tank in the figure is fabricated from spirally wrapped metal plates that are welded ...
The pressure tank in the figure is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown where Assume 53. The tank has an inside diameter of 65 in. and a wall thickness of 0.29 in. Determine the largest allowable gage pressure if the allowable normal stress perpendicular to the weld is 11.9 ksi and the allowable shear stress parallel to the weld is 8.9 ksi es
The pressure tank in the figure is...
Q3 (30) A cylindrical pressure vessel is constructed from a long, narrow steel plate by wrapping...
Q3 (30) A cylindrical pressure vessel is constructed from a long, narrow steel plate by wrapping the plate around a mandrel and then welding along the edges of the plate to make a helical joint α 55° with the longitudinal axis. The vessel has inner radius r-1.8 m and wall thickness t 20 mm. The material is steel with modulus E: 200 GPa and Poisson's ratio0.30. The internal pressure p is 800 kPa Helical weld . The helical weld makes...
Prob #4 A cylindrical thank is designed to withstand an internal pressure of3 MPa. The tank...
Prob #4 A cylindrical thank is designed to withstand an internal pressure of3 MPa. The tank has an inner diameter of 4 m and the wall thickness is 40 mm. The tank is fabricated by bolting together (on both sides of the vssel) two half-cylindrical longitudinal thin shell sections as shown. The diameter of the bolts is 25mm and the bolts are made from a material with allowable stress of 250 MPa 18. The hoop stress sustained by the tank...
P14.011 The pressure tank is fabricated from spirally wrapped metal plates that are welded at the...
P14.011 The pressure tank is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 780 mm and a wall thickness of 10.3 mm. For a gage pressure of 1.23 MPa, determine (a) the normal stress perpendicular to the weld (use positive for tension, negative for compression) and (b) the shear stress (absolute value) parallel to the weld. Assume B 56 Answers: (e) Normal stress -MPa (b)...
The cylindrical portion of the gas storage tank is fabricated by boting together two half cylindrical...
The cylindrical portion of the gas storage tank is fabricated by boting together two half cylindrical thin shells. Each half cylinder has a radius, R, and a thickness, t. Determine the number of fasteners required in one meter of length on one side of the tank bolted connection given: R = 0.55 m t + 1.2 mm de 9 mm Tank internal pressure = 1.8 MP Fastener allowable stress = 385 MPa Number of fasteners required in one meter of...
The cylindrical pressure vessel has an inner radius of 1.25 m and a wall thickness of...
The cylindrical pressure vessel has an inner radius of 1.25 m
and a wall thickness of 25 mm . It is made from steel plates that
are welded along the 45∘ seam. The vessel is subjected to an
internal pressure of 7 MPa . (Figure 1)
Part A
Determine the normal stress component along this seam.
Express your answer to three significant figures and include the
appropriate units.
Part B
Determine the shear stress component along this seam.
Express your...
em 35? ? A cylindrical pressure vessel is constructed from a long, narrow steel plate by...
em 35? ? A cylindrical pressure vessel is constructed from a long, narrow steel plate by wrapping the plate around a mandrel and then welding along the edges of the plate to make a helical joint. The helical weld makes an angle ? 350 with the axial direction. The vessel has inner radius r = 1.8 m and wall thickness 20 mm. The material is steel with E 200 GPa and Poisson ratio 0.3. The internal pressure p = 800...
- 3. A propane storage tank is constructed by welding two hemispherical end caps onto a cylindrical main body. The cylindrical body is manufactured from a helical welded pipe which has an outside diameter of 750 mm and a wall thickness of 6 mm. The tank is designed to hold gas at an internal gauge pressure of 6 MPa. a) Draw the Mohr’s circle and determine the normal and shear stresses on the weld in the cylindrical main body portion...
A cylindrical pressure vessel of 250 mm mean diameter and 6 mm
wall thickness is fabricated from a 1.2 m length of spirally welded
pipe AB as shown. Tank gauge pressure is 4 MPa and centric axial
forces P and P1 of 240 kN act through rigid end plates. Determine:
(a) Net longitudinal and hoop stresses. (b) Normal stress acting
perpendicular to weld and shear stress parallel to weld (show
sketch of Mohr’s circle). (c) Determine the Factor of Safety...
The pressure tank in the figure is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown where Assume 53. The tank has an inside diameter of 65 in. and a wall thickness of 0.29 in. Determine the largest allowable gage pressure if the allowable normal stress perpendicular to the weld is 11.9 ksi and the allowable shear stress parallel to the weld is 8.9 ksi es
The pressure tank in the figure is...
Q3 (30) A cylindrical pressure vessel is constructed from a long, narrow steel plate by wrapping the plate around a mandrel and then welding along the edges of the plate to make a helical joint α 55° with the longitudinal axis. The vessel has inner radius r-1.8 m and wall thickness t 20 mm. The material is steel with modulus E: 200 GPa and Poisson's ratio0.30. The internal pressure p is 800 kPa Helical weld . The helical weld makes...
Prob #4 A cylindrical thank is designed to withstand an internal pressure of3 MPa. The tank has an inner diameter of 4 m and the wall thickness is 40 mm. The tank is fabricated by bolting together (on both sides of the vssel) two half-cylindrical longitudinal thin shell sections as shown. The diameter of the bolts is 25mm and the bolts are made from a material with allowable stress of 250 MPa 18. The hoop stress sustained by the tank...
P14.011 The pressure tank is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 780 mm and a wall thickness of 10.3 mm. For a gage pressure of 1.23 MPa, determine (a) the normal stress perpendicular to the weld (use positive for tension, negative for compression) and (b) the shear stress (absolute value) parallel to the weld. Assume B 56 Answers: (e) Normal stress -MPa (b)...
The cylindrical portion of the gas storage tank is fabricated by boting together two half cylindrical thin shells. Each half cylinder has a radius, R, and a thickness, t. Determine the number of fasteners required in one meter of length on one side of the tank bolted connection given: R = 0.55 m t + 1.2 mm de 9 mm Tank internal pressure = 1.8 MP Fastener allowable stress = 385 MPa Number of fasteners required in one meter of...
The cylindrical pressure vessel has an inner radius of 1.25 m
and a wall thickness of 25 mm . It is made from steel plates that
are welded along the 45∘ seam. The vessel is subjected to an
internal pressure of 7 MPa . (Figure 1)
Part A
Determine the normal stress component along this seam.
Express your answer to three significant figures and include the
appropriate units.
Part B
Determine the shear stress component along this seam.
Express your...
em 35? ? A cylindrical pressure vessel is constructed from a long, narrow steel plate by wrapping the plate around a mandrel and then welding along the edges of the plate to make a helical joint. The helical weld makes an angle ? 350 with the axial direction. The vessel has inner radius r = 1.8 m and wall thickness 20 mm. The material is steel with E 200 GPa and Poisson ratio 0.3. The internal pressure p = 800...
Most questions answered within 3 hours.
-
how to select perpendicular gd&t tolerance value
using IT tolerance. and gave example
asked 2 minutes ago -
plz explain: A sound that changes pressure from 100 mPa to 10
mPa has a change...
asked 2 minutes ago -
What is the measured air concentration from a sample that has 38
μg of contaminant when...
asked 21 minutes ago -
In support of the argument that we have free will, what are the
implications of seemingly...
asked 22 minutes ago -
Share your thoughts concerning the pros and cons of using
natural products as anticancer agents. (please...
asked 32 minutes ago -
Describe in detail how your own actions reflect the
ideas shared in the discussion, and relate...
asked 36 minutes ago -
Name and clearly describe one technique for determining the age
of fossils in geological context. Are...
asked 50 minutes ago -
A ball is thrown with an initial velocity of 20.0 m/s at an
angle of 35.00...
asked 43 minutes ago -
When assessing pension risk, analysts compute ratios for both
long- and short-term risk. Which statement below...
asked 42 minutes ago -
What is the relativistic momentum of a proton traveling at
0.990c?
A. 3.55E–18 kg·m/s
B. 3.52E–18...
asked 51 minutes ago -
Question 1: B cells secrete these types of immunoglobulin
antibodies. Choose all correct.
1. IgD
2....
asked 58 minutes ago -
Please show calculations for this question:
The average income of university graduates is $68,500 with a...
asked 1 hour ago