I need help completing this in multisim
After simulating the circuit in multisim following pattern sequence was generated;
Pattern generator output Patterns:
Pattern |
ABCD |
Pattern |
ABCD |
0 |
1101 |
8 |
0001 |
1 |
0110 |
9 |
0000 |
2 |
0011 |
10 |
1000 |
3 |
1001 |
11 |
1100 |
4 |
0100 |
12 |
1110 |
5 |
1010 |
13 |
0111 |
6 |
0010 |
14 |
1011 |
7 |
0010 |
15 |
1101 |
For other variables as a feedback to the XNOR gate;
For QA and QB as feedback inputs we get following output patterns;
Pattern |
ABCD |
Pattern |
ABCD |
0 |
1101 |
8 |
0010 |
1 |
0110 |
9 |
1001 |
2 |
0011 |
10 |
0100 |
3 |
1001 |
11 |
0010 |
4 |
0100 |
12 |
1001 |
5 |
0010 |
13 |
0100 |
6 |
1001 |
14 |
0010 |
7 |
0100 |
15 |
1001 |
Thanks Kindly feel free to discuss the dificulties if any.
I need help completing this in multisim 8. Load the circuit E6B-3.MS7, shown in Figure 6B.3....
I need to complete the following task in multisim.
2. Circuit E10-2.MS7, shown in Figure 10.2, performs the same logic function as the half adder This part is in the Miscellaneous Digital parts bin HALF ADDER Figure 10.2: Simplified half adder circuit Test the circuit to verify its operation. 3. Afull adde? adds three bits together. The A and B inputs, as well as a Carry input, are added. Figure 10.3 shows the diagram of the full adder. Load circuit...
I need help in multisim
1. Load the circuit E7A-1.MS7, shown in Figure 7A.1 2. 5 v 5 V 250 Hz S V INA INB QB RO1 RO2 R91 R92 7490N Figure 7A.1: 7490 decade counter The 7490 decade counter is wired internally to reset from nine back to zero. Verify that the counting sequence goes from zero to nine 2. What happens if both RO inputs are pulled high while the 7490 is counting? Demonstrate this in the circuit...
Need help with this. Circuits need to be done on Multisim. I will give you a good rating if you can help me out. Consider a two-diode AND logical gate circuit. Calculate and build a table showing the values of output voltages for 4 different combinations of input voltages. Simulate the circuit in Multisim for all above values of the input voltages, and observe the actual values of the output voltage. Add the simulation results to the table, compare, analyze,...
3.4.1 Build and simulate the comparator circuit shown in Figure 3, in Multisim. The inputs A3, A2, A1, 40 act as the first 4-bit binary number, and B3, B2, B1, BO act as the second 4-bit binary number. Run your circuit for different setting of the inputs as in Table 3 and observe how the output Xchecks if the numbers are equal or not. Note: connect the eight inputs of this circuit to an 8-input DIP switch as shown in...
Could someone please help me on how I should be configuring the
circuit in Figure 4(a) in Multisim? Basically not understanding
question #1 in the Procedure. Cannot keep Vrb the same value while
adjusting Vcc. Then when trying to adjust Vbb to hold Vrb, Ib
changes.
Any help is appreciated!
Discrete Devices Section LAB 4 BJT CHARACTERISTICS AND BIASING Objective: The objective of this laboratory is to examine the operation of a bipolar junction transistor and plot its output characteristics...
You will build a seven-segment display decoder, shown in Figure 3. The circuit has four input bits, D3:0 (representing a hexadecimal number between 0 and F), and produces seven output bits, Sa:g, that drive the seven segments to display the number. The 7-segment display we will use in this lab is a common cathode type, a segment of the display turns on when it is 1. The other type of 7-segment display is common anode, for which a segment turns...
ONLY NEED HELP WITH III and IV PLEASE
(e) A second stage, shown in Figure 3, is cascaded directly after the output of the circuit in Figure 1 R4 Figure 3 (i) Show that the combined response of the complete circuit is given by: (4 marks) (ii) The two cascaded stages form a bandpass filter, which only amplifies a specific range of frequencies. This range of frequencies is known as the passband. Using the values chosen in (a) for Figure...