The motor shown below runs at 2000 rpm transmitting power to another shaft connected through flat...
Q2. Figure Q2 shows a shaft which transmits a power of 48 kW through flat belts. Pulley A is driven by a motor which rotates at 3000 rpm. The diameter of pulley A is 400 mm and that of pulley B is 250 mm. The thickness of the belts is 4 mm and they are made of a material with density of 1100 kg/m3. Assume no sliding between pulleys and belts a) Calculate the speed of the belt and the...
Determine the number of V-belts required to transmit a power of 60 kW at 750 rpm from an electric motor to a compressor shaft at 300 rpm. The larger pulley diameter is 1500 mm. The centre distance is 1650 mm, and overload factor is to be taken as 1.5. A belt with cross- sectional area of 350 mm², density of 1000 kg/m and having an allowable tensile strength of 2 MPa is available for use. The coefficient of friction between...
Q.9. Arubberised flat belt is moving at 14 m/s with the tension in the tight side of 10.0 kN and the slack side of 5.0 kN. The belt is 350 mm wide and 10 mm thick, and it is constructed of 5 plies of 32 oz canvas ducking. What is tension ratio in the belt? A. 2.0 В. 2.1 С. 1.9 D. 2.3 E. none of above (4 Marks) Q.10. A V-belt drive system is to be designed to transmit...
Q1 A belt drive and pulley arrangement is designed to transmit 75 kW of power at 1200 rpm, generated by a six-pole squirrel-cage induction motor. The belt connects two shafts 3 m apart, with axes in the same horizontal plane. The driven shaft runs at half the angular speed of the driver and it runs a light shock machinery. As a design engineer you need to do the following; i. Design shafts suitable for this application (20 marks) ii. Select...
A single V-belt drive system is powered by an electric motor with a speed of 2691 rpm and transmits a power 11 kW. The driving pulley is connected to the driven pulley by a single V-belt of angle 18 degrees and a unit weight of 2.18 N/m. The angle of wraps between the belt and pulley is approximately 175 degrees. The driven shaft is attached to a cylindrical pulley of 101 mm and runs at a speed of 1221 rpm....
PROBLEM 3: Figure 3 shows a top view ofa motor driven pump. The direction of the gravitational acceleration is indicated by g, and is oriented orthogonal to this paper. The shaft of the motor is supported by two bearings in points A and B and the motor rotates at n 1000 rpm. The motor power is 10 kW. The radius of pulley A and B. a-,3 = 40 mm. Each pulley weighs 5 kg. The pump shaft is supported by...
need help asap please Question 5-6 Marks A motor runs a pump via a system as shown below. Determine the following The maximum power if one V-belt is used a) The maximum power if 2 V-belts identical to the V-belt in a) are used b) The maximum power if one V-belt with twice the cross sectional area as in a) is used c) Mots The conditions of the system are as follows: Pulley radius = 120 mm =160° f =...
Figure 1 shows the layout of countershaft used to transmit power to a blower through a pulley drive (4-5). Pulley (driving sheave) 4 has a diameter of 125-mm and pulley (driven sheave) 5 has a diameter of 75 mm. Pulley 5 is mounted vertically below pulley 4 (as shown in the figure). Belt tension on the loose side is 20% of the tension on the tight side. A power of 7.5 kW is transmitted via the gear set (2-3) from...
please solve with details Question#1140Marksl The shaft shown in the figure is rotating at 650 rpm and it receives 5592.75 W through a flexible coupling at its right end. The power is delivered to an adjacent shaft through a single helical gear B having a normal pressure angle of 20° and a helix angle of 15o. The pitch diameter for the gear is 105.1814 mm (4.141 in). A spacer is used to position the gear relative to bearing C. The...
find v belt drive design power select belt type determine shive size (belt speed 4000 ft/min) find shive size from power rating figure find rated power find estimated centre distance find belt length (by selecting standard belt length) calculate actual centre distance find contact angle for small shieve determine correct factors calculate correct power per belt no. of belt needed V-Belt Designing Sample Problem . Given: A 4 cylinder diesel engine runs at 80 hp, 1800 rpm, to drive a...