Homework Answers
Add Answer to:
A centrifugal pump is pumping water at a rate of 35.55 gal/min. The pressures at the...
4. The discharge pressure gauge reading is 5 lb/in2 (psi) for the pumping system shown in the ske...
4. The discharge pressure gauge reading is 5 lb/in2 (psi) for the pumping system shown in the sketch below, with the outlet nozzle discharging a 2-inch diameter stream of water directly to the atmosphere. The gauge pressure at the pump suction inlet at the point of incipient cavitation is (-2,071.12) lb/ft, i.e., for vapor pressure of water at 68° F of 50.54 lb/ft2 absolute, and standard atmospheric pressure 30 in Hg. Friction losses in the suction piping from the reservoir...
7.14 The pump in Fig. 7.20 delivers water from the lower to the upper reservoir at the rate of 0.057 m3/s. The energy loss between the suction pipe inlet and the pump is 1.83 m and that between t...
7.14 The pump in Fig. 7.20 delivers water from the lower to the upper reservoir at the rate of 0.057 m3/s. The energy loss between the suction pipe inlet and the pump is 1.83 m and that between the pump outlet and the upper reservoir is 3.66 m. Both pipes are 6-in Schedule 40 steel pipe. Calculate (a) the pressure at the pump inlet, (b) the pressure at the pump outlet, (c) the total head on the pump, and (d)...
Question 3 Show that the pressure head rise in the impeller of a centrifugal pump when...
Question 3 Show that the pressure head rise in the impeller of a centrifugal pump when frictional and other losses in the impeler are neglected, is given by (a) where Vni is the velocity of flow at the inlet, while at the outlet of the backward curved blades, u2, m2, and ßz are the blade velocity, velocity of flow and blade angle, respectively. (4 marks) A centrifugal pump rotating at 1450 rpm discharges 0.015 m'ls of water. Its impeller has...
6. Determine the setting of a centrifugal pump, given that flow rate = 2.4 m/min; diameter...
6. Determine the setting of a centrifugal pump, given that flow rate = 2.4 m/min; diameter of intake pipe = 160 mm; entrance losses = one velocity head in suction pipe; required NPSH = 42 kPa; water temperature = 30°C N D1, D2 : inlet and outlet diameters of impeller (rotor) b : impeller width 0,6 : inlet and outlet impeller vane angles (degrees) : speed of rotation of impeller (and its driver) in rpm V, V :tangential and radial...
1. A centrifugal pump performance data are shown in the following table for water. Pump speed-250...
Mechanical Lab II. Please answer asap with clear work. Thank
you!
1. A centrifugal pump performance data are shown in the following table for water. Pump speed-2500 RPM Pa or P2 (bar) P. or Pi (bar) Volume of water(L Time (sec) Input-Power (W) -0.3 20 60 100 For this data set, calculate the following i. Pump discharge capacity Q (LUs and GPM) ii. Pump head H (m and ft) iii. Fluid power Pr (Watt) iv. Brake power Pb (Watt) v....
An oil pump is drawing 44kW of electric power while pumping oil with p = 860...
An oil pump is drawing 44kW of electric power while pumping oil with p = 860 kg/m^3 at a rate of 0.1 m^3/s. The inlet and outlet diameters of the pipe are 8cm and 12cm, respectively. If the pressure rise of oil in the pump is measured to be 500 kPa and the motor efficiency is 90 percent, determine the mechanical efficiency of the pump.
3. A centrifugal pump performance data are shown in the following table for water. Pump speed...
3. A centrifugal pump performance data are shown in the following table for water. Pump speed 2500 RPM Pe or P2 (bar) P or Pi (bar) Volume of water (L) Time (sec) Input-Power (W -0.3 20 60 100 For this data set, calculate the following: i. Pump discharge capacity Q (L/s and GPM) ii. Pump head H (m and f) iii. Fluid power Pr(Watt) iv. Brake power Pb (Watt) v. Pump overall efficiency η (%) vi. Flow rate coefficient Ca...
Fluid Mechanics & Fluid Power Determine the NPSH available. The pressure in the tank is - 20 kPa at 70 °C (atmospheric pressure is 100.5 kPa). The water level in the tank is 2.5 above the pump in...
Fluid Mechanics & Fluid Power
Determine the NPSH available. The pressure in the tank is - 20 kPa at 70 °C (atmospheric pressure is 100.5 kPa). The water level in the tank is 2.5 above the pump inlet. The pipe is 1%", schedule 40 with a total length of 12 m. The elbow is standard, and the globe valve is fully open. The flow rate is 95 L/min. FIGURE 13.27 llustration of pump performance for different impeller diameters with net...
(5 pts) A pump is pumping water from a lake to the top of a mountain...
(5 pts) A pump is pumping water from a lake to the top of a mountain through a constant- diameter pipe. Water exits the pipe at a volumetric flow rate of 0.04 m/s. The vertical distance between the lake surface and the pipe exit at the top of the mountain is 100 m. The diameter of the pipe is 10 cm. All mechanical energy losses are negligible and the flow is steady and incompressible. (Water density-I g/cm, ?-I.) Determine a)...
Problem 5: The 28-in-diameter pump in the Figure at 1170 r/min is used to pump water at 20°C through a piping system at 14,000 gal/min. (a) Determine the required brake horsepower. The average fricti...
Problem 5: The 28-in-diameter pump in the Figure at 1170 r/min is used to pump water at 20°C through a piping system at 14,000 gal/min. (a) Determine the required brake horsepower. The average friction factor is 0.018. (b) If there is 65 ft of 12-in-diameter pipe upstream of the pump, how far below the surface should the pump inlet be placed to avoid cavitation? Given that the water at 20 °C has a specific weight of 62.4 lbf/ft and vapor...
4. The discharge pressure gauge reading is 5 lb/in2 (psi) for the pumping system shown in the sketch below, with the outlet nozzle discharging a 2-inch diameter stream of water directly to the atmosphere. The gauge pressure at the pump suction inlet at the point of incipient cavitation is (-2,071.12) lb/ft, i.e., for vapor pressure of water at 68° F of 50.54 lb/ft2 absolute, and standard atmospheric pressure 30 in Hg. Friction losses in the suction piping from the reservoir...
7.14 The pump in Fig. 7.20 delivers water from the lower to the upper reservoir at the rate of 0.057 m3/s. The energy loss between the suction pipe inlet and the pump is 1.83 m and that between the pump outlet and the upper reservoir is 3.66 m. Both pipes are 6-in Schedule 40 steel pipe. Calculate (a) the pressure at the pump inlet, (b) the pressure at the pump outlet, (c) the total head on the pump, and (d)...
Question 3 Show that the pressure head rise in the impeller of a centrifugal pump when frictional and other losses in the impeler are neglected, is given by (a) where Vni is the velocity of flow at the inlet, while at the outlet of the backward curved blades, u2, m2, and ßz are the blade velocity, velocity of flow and blade angle, respectively. (4 marks) A centrifugal pump rotating at 1450 rpm discharges 0.015 m'ls of water. Its impeller has...
6. Determine the setting of a centrifugal pump, given that flow rate = 2.4 m/min; diameter of intake pipe = 160 mm; entrance losses = one velocity head in suction pipe; required NPSH = 42 kPa; water temperature = 30°C N D1, D2 : inlet and outlet diameters of impeller (rotor) b : impeller width 0,6 : inlet and outlet impeller vane angles (degrees) : speed of rotation of impeller (and its driver) in rpm V, V :tangential and radial...
Mechanical Lab II. Please answer asap with clear work. Thank
you!
1. A centrifugal pump performance data are shown in the following table for water. Pump speed-2500 RPM Pa or P2 (bar) P. or Pi (bar) Volume of water(L Time (sec) Input-Power (W) -0.3 20 60 100 For this data set, calculate the following i. Pump discharge capacity Q (LUs and GPM) ii. Pump head H (m and ft) iii. Fluid power Pr (Watt) iv. Brake power Pb (Watt) v....
3. A centrifugal pump performance data are shown in the following table for water. Pump speed 2500 RPM Pe or P2 (bar) P or Pi (bar) Volume of water (L) Time (sec) Input-Power (W -0.3 20 60 100 For this data set, calculate the following: i. Pump discharge capacity Q (L/s and GPM) ii. Pump head H (m and f) iii. Fluid power Pr(Watt) iv. Brake power Pb (Watt) v. Pump overall efficiency η (%) vi. Flow rate coefficient Ca...
Fluid Mechanics & Fluid Power
Determine the NPSH available. The pressure in the tank is - 20 kPa at 70 °C (atmospheric pressure is 100.5 kPa). The water level in the tank is 2.5 above the pump inlet. The pipe is 1%", schedule 40 with a total length of 12 m. The elbow is standard, and the globe valve is fully open. The flow rate is 95 L/min. FIGURE 13.27 llustration of pump performance for different impeller diameters with net...
(5 pts) A pump is pumping water from a lake to the top of a mountain through a constant- diameter pipe. Water exits the pipe at a volumetric flow rate of 0.04 m/s. The vertical distance between the lake surface and the pipe exit at the top of the mountain is 100 m. The diameter of the pipe is 10 cm. All mechanical energy losses are negligible and the flow is steady and incompressible. (Water density-I g/cm, ?-I.) Determine a)...
Problem 5: The 28-in-diameter pump in the Figure at 1170 r/min is used to pump water at 20°C through a piping system at 14,000 gal/min. (a) Determine the required brake horsepower. The average friction factor is 0.018. (b) If there is 65 ft of 12-in-diameter pipe upstream of the pump, how far below the surface should the pump inlet be placed to avoid cavitation? Given that the water at 20 °C has a specific weight of 62.4 lbf/ft and vapor...
Most questions answered within 3 hours.
-
An object in front of a concave mirror has a real image that is
11.5 cm...
asked 7 minutes ago -
Consider the reaction, C3 H8 + O2 --> CO2 + H2O. How many
moles of O2...
asked 1 hour ago -
You and your opponent both roll a fair die. If you both roll the
same number,...
asked 2 hours ago -
In a study of the accuracy of fast food drive-through orders,
Restaurant A had 257 accurate...
asked 2 hours ago -
Identify and describe in detail the four categories of
institutions that could be included in a...
asked 2 hours ago -
In python
class Customer:
def __init__(self, customer_id, last_name, first_name, phone_number, address):
self._customer_id = int(customer_id)
self._last_name =...
asked 2 hours ago -
What is an example of a limitation in implementing a new
ERP system and how it...
asked 2 hours ago -
In a section of 9.7cm of an artery with a radius of 2.6mm there
is a...
asked 2 hours ago -
the two carboxylic acid groups of aspartic acid have different
acidities with pKa values of 2.1...
asked 2 hours ago -
Would CuCO3 aqueous salt combined with calcium chloride
form a solid precipitate? If so, what would...
asked 2 hours ago -
How do ECM Solutions assist in embedding a culture of continuous
improvement in an organization? (Project...
asked 2 hours ago -
Directions
These directions introduce the idea of Essential Questions.
Since this may be a new concept...
asked 2 hours ago