I need to measure in multisim, not calculate on paper. Im not sure how to connect the ocilliscope to find vin and vout. Thanks in advance
We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
I need to measure in multisim, not calculate on paper. Im not sure how to connect...
for
the same black box circuit how do we measure the output voltage to
calculate the gain because the input voltage is 12V and which
values should we set for the frequency is it Hz or kHz
this is the question and
i kniw hot to connect the circuit to the oscilloscope and signal
generator but im not sure what frequency values to set on the
signal generator and also i dont know how to get the gain from the...
Hi! I need help with a practice problem. Im not quite sure how to solve it. Thank you in advance! Let f(n) = log3n + 1. Prove f(n) is O(log19n). Hint: Use the change of base formula for logs.
I need help with this. I am unfamiliar with Ltspice and want to
make sure I am doing this right. Please be thorough with your
explanations.
. Design a high pass filter (Fig. 1) which has a break point fo 1 kHz at 3dB below the midband level (the -3dB point) Uses a C01uF capacitor, and calculate the value for R Vout C 0.1uF、 Vin 5Vac OVdc 2. Use LTspice to perform an AC sweep of your designed circuit from...
I need help to measure the high frequency cutoff. The circuit
below is for HIGH PASS FILTER
I made it but I dont know how to accurately measure the high
cutoff as what we did in the lab. in the lab we get 14.35
kHz but when I try in the multisim and varing the freqency
as shown in the table below I dont get any change.
Please do it in multisim and explain your answer, thanks.
f
1-kHz
2-kHz...
Simulation For each filter mentioned in the following cases, first simulate the circuit using Multisim. You can get a plot of the transfer function that is called the Bode plot. From the right toolbar, select "Bode Plotter". Change initial (I) and final (F) frequencies to 1Hz and 200 KHz, respectively. Use a Voltage AC source as the input signal. You do not need to change any parameter from voltage AC source. Connect "Bode Plotter" to input and output of your...
For each filter mentioned in the following cases, first simulate the circuit using Multisim. You can get a plot of the transfer function that is called the Bode plot. From the right toolbar, select "Bode Plotter". Change initial (I) and final (F frequencies to 1Hz and 200 KHz, respectively. Use a Voltage AC source as the input signal. You do not need to change any parameter from voltage AC source Connect "Bode Plotter" to input and output of your circuit...
I am having trouble answering this question. Im not sure if you
need more information but the homework doesn't say exactly what
information I need. I cannot find it in my book in this chapter.
Long Problem 1 - similar to Serway 22.35 Determine the critical angle for fused quartz surrounded by water. You may assume both the water and the quartz have temperature 20°C, and the light has wavelength of 589nm so that you can use information provided in...
Anything would be help please help me
OBJECTIVES Study the behavior of capacitors while charging Learn how changing the values of R or C in a series RC circuit affects the charging time Learn the behavior of capacitor and inductor in a DC circuit 1. 2. 3. EQUIPMENT Breadboard, Multimeter, DC power supply, Oscilloscope, Resistor, Capacitor (values will be provided in lab) Connect the given circuit and notice how the capacitor charges Measure the voltage across the resistor, and across...
I need help understanding how to complete this question. I am
not sure if the items in the table are correct, except I do know
that the weight of the paper is correct.
calculate how many moles of CaCl2•2H2O are present in 1.50 g of
CaCl2•2H2O and then calculate how many moles of pure CaCl2 are
present in the 1.50 g of CaCl2•2H2O. Record the answers in
Data Table 1.
Use the information and examples provided in the Exploration and...
Hello, I am asked to determine whether there is 1, 2, or no
triangles. I am not sure on how I am supposed to do this. I started
by using the law of sines and show the steps on my paper. Please
correct me if I am wrong. If I am going in the right direction
please tell me what else I need to do. Please provide steps if
possible thanks! Ignore the pink highlighted numbers
0cmie whehs or nu...