Question 1: (Design Tension member) Design the x-bracing of a building, which is subjected to tension...

Question

Question

Question 1: (Design Tension member) Design the x-bracing of a building, which is subjected to tension force due to wind load.

Answer 1

Answer #1

Answer 2

Similar Homework Help Questions

A double-angle tension member, 2L 3x2x 1/4, is subjected to a dead load of 12 kips

A double-angle tension member, 2L 3x2x 1/4, is subjected to a dead load of 12 kips, and a live load of 36 kips. It is connected to a gusset plate with one line of 3/4-inch-diameter bolts through the long legs. Is this member safe? Assume U=0.85. Fy =36 ksi and Fu = 58 ksi.
Steel Design 2. (50 pts) Design an A36-steel tension member 16 ft long consisting of two...

Steel Design 2. (50 pts) Design an A36-steel tension member 16 ft long consisting of two channels, bolted through their webs to a single 1 inch gusset plate, to transmit 75 kips DL and 93 kips LL. The bolts are 7/8 in. Bolt spacing 4 inch and bolt edge distance 3 inch. In addition to checking block shear in the channels, design the thickness of the gusset plate to resist block shear.
2. (30 pts) Determine the block shear strength of the tension member shown below. Bolts diameter...

2. (30 pts) Determine the block shear strength of the tension member shown below. Bolts diameter = 7/8 in, A36 steel is used (Table 2-4 XN, A16 s 58 kse DO 3232 -in. bolts 19 (3) /8" bolts 3" bolt spacing (fy = 36 ksi P. 2-487 (Table 1-7) Ag = 2.50 in ² p. 1-48 - 1.00 in t. 3/8" And = [3.5"-(7/6" + /6")] (3/8") = 10.94 in? Ag. = (7.5") (2/6") - 2.81 in? Anu = [7.5...

3. A C 9x15 is to be used as a tension member. The channel is bolted to a 5/8 in gusset plate wit...

3. A C 9x15 is to be used as a tension member. The channel is bolted to a 5/8 in gusset plate with 7/8 inch diameter, A307 bolts. The tension member is AS72 Grade 50 steel and the gusset plate is A36. Follow Figure 3. (a) Check all spacing and edge distance irements; (b) Compute the design strength based on shear and bearing; and (c) Compute the allowable strength based on shear and bearing. 23" 3" 3" С 9x 15...
2_...-3.5.1.3.5. 1 2 Q.4. A C7 x 9.8 tension member is connected to a 2/7-in.-thick gusset...

2_...-3.5.1.3.5. 1 2 Q.4. A C7 x 9.8 tension member is connected to a 2/7-in.-thick gusset plate. Both the member and the gusset plate are A36 steel C79.8 O o o a) (15%) Compute the available block shear strength of the tension member for LRFD b) (10%) Compute the available block shear strength of the gusset plate for LRFD t-217 Wh-diameter bolts
Design a single equal-angle tension member. It is 4m long and subjected to a tensile load...

Design a single equal-angle tension member. It is 4m long and subjected to a tensile load of 25T. It is connected to a gusseted plate through one leg only. Assume bolt of 16mm. σt = 1500kg/cm2. Check for slenderness ratio. Given rmin = 1.94cm.

The tension member shown in Figure 1 is subjected to a tensile force T. The member...

The tension member shown in Figure 1 is subjected to a tensile force T. The member has an L89x89x7.9 cross-section with 350W steel. The member is connected to a gusset plate through four A325 bolts having 3/4"(19 mm) diameter as shown. The threading can be assumed to intercept the plane of shear and the connection is short. The dimensions taken are a=30mm, b=60mm, and c=40mm. (a) Determine the tensile resistance of the member based on the potential failure trajectories 1-1...
Question 1: Three tension members are shown below. Assume the strength of the member controls and...

Question 1: Three tension members are shown below. Assume the strength of the member controls and not the connecting element. Each member is made from A36 steel. All bolts are spaced at 3.0 inches unless the sketch indicates otherwise. The distance from the centerline of the last bolt to the end of the tension member is 2.0 inches unless the sketch indicates otherwise. The required sketches described below are 20% of the points Include the following: For the area calculations...