3. A C 9x15 is to be used as a tension member. The channel is bolted to a 5/8 in gusset plate wit...
Steel Design 2. (50 pts) Design an A36-steel tension member 16 ft long consisting of two channels, bolted through their webs to a single 1 inch gusset plate, to transmit 75 kips DL and 93 kips LL. The bolts are 7/8 in. Bolt spacing 4 inch and bolt edge distance 3 inch. In addition to checking block shear in the channels, design the thickness of the gusset plate to resist block shear.
S- Section FIGURE P3.2-3 APL⅜x6tension member is steel is A36. Assume that A, A, and compute the following. a. The design strength for LRFD. b. The allowable strength for ASD. 32-4 APLx6 tension member is welded to a gusset plate as shown in Figure P3.2-4. The :and compute 3.2-4 ameter bolts, as shown A,A, and compute the FIGURE P3.2-4 ion member shown in Figure P3.2.5 is a PL tax 8 of A36 steel. The mem- ted to a gusset plate...
5. Using AISC Steel Construction Manual, find the following design strengths of 1-inch Group A bolts on A36 gusset plates, type N, with STD holes, 3" bolt spacing and 2" edge distance: (5 points) a. Shear Strength of Bolts in Single Shear Connections b. Shear Strength of Bolts in Double Shear Connections c. Tensile Strength of Bolts d. Bearing Strength at Bolt Holes for Inner Bolts e. Bearing Strength at Bolt Holes for Edge Bolts 5. Using AISC Steel Construction...
2_...-3.5.1.3.5. 1 2 Q.4. A C7 x 9.8 tension member is connected to a 2/7-in.-thick gusset plate. Both the member and the gusset plate are A36 steel C79.8 O o o a) (15%) Compute the available block shear strength of the tension member for LRFD b) (10%) Compute the available block shear strength of the gusset plate for LRFD t-217 Wh-diameter bolts
An L5x5x1/2 tension member of A588 steel is connected to a gusset plate with ¾-in diameter bolts as shown in Figure 1. Assume block shear is not a concern. Use the alternative value of U from AISC Table D3.1 a.) The LRFD tension rupture strength (Pn) of the member is? b.) The LRFD tension strength (Pn) of the member is? L5x5x22 OOOOOO 1S w befo-soprano-belim 5 spaces @ 3" - = 15" Figure 1
Pleqse show details and formulas. Select a single-angle tension member of A36 steel to resist a dead load of 20 kips and a live load of 50 kips. The length of the member is 20 feet, and it will be connected to a %-inch thick gusset plate with one line of 3/4-inch- diameter bolts through the long legs. There will be four or more bolts in this Q1) line Select a single-angle tension member of A36 steel to resist a...
Q2) American Standard Channel shape, C10 x 20, is connected to a gusset plate with 3/4-inch-diameter bolts as shown below. The steel is A36. If the member is subjected to dead load and live load only, what is the service dead load capacity if the live-to-dead load ratio is 3? Assume that Ac = 0.85A. O 0 O 0 O 0 C10 X 20
The tension member shown in Figure 1 is subjected to a tensile force T. The member has an L89x89x7.9 cross-section with 350W steel. The member is connected to a gusset plate through four A325 bolts having 3/4"(19 mm) diameter as shown. The threading can be assumed to intercept the plane of shear and the connection is short. The dimensions taken are a=30mm, b=60mm, and c=40mm. (a) Determine the tensile resistance of the member based on the potential failure trajectories 1-1...
A single L8×6×1/2 is used as a tension brace in a multi-story building. The 8 inch leg of the angle is attached to a gusset plate with two lines of four 3/4 inch bolts at a spacing of 3 inch. Determine the effective net area. Question 3 A single L8x6x1/2 is used as a tension brace in a multi-story building. The 8 inch leg of the angle is attached to a gusset plate with two lines of four 3/4 inch...
Question 8. Section 2-3 Shear Stresses 6. In the bolted connection of Fig. 2-8, assume that the bolts are , in. in diameter and that the allowable shear stress for the bolts is 14,500 psi. Based on bolt shear only, compute the safe allowable load P that may be applied 7. Compute the force required to punch a 1 in. diameter hole through a ½ in, thick boiler plate. The ultimate shear strength for the material is 42,000 psi. 8....