Homework Answers
Ans:1 as Vin=0v, base current is zero,transistor is in off condition ,collector corent is also zero, so VCE=VCC=10v
Ans: 2 when transistor saturates Vce=0v, collector current Ic=Vcc/Rc =10/Rc
Ib= (1/200) Ic =1/20Rc
Ans:3 in question R5 is written but it is not found in figure,and question is also not fully please provide other details so you can get answer for it
Add Answer to:
give direct answers please
no
problem
Q9 For the transistor circuit in Figure 29. Answer the...
1. For the transistor circuit shown in figure 1, what is: a. Vce when VIN =...
1. For the transistor circuit shown in figure 1, what is: a. Vce when VIN = OV? b. What minimum value of IB is required to saturate the transistor if Boc is 200? c. Calculate the maximum value of Rs when Vin = 5V. VCC 10V RC 1.0 K RB Q1 VIN=0V 15C02MH-TLE GND Figure
Figure 3 Transistor amplifire circuit with source Vs and load R b) For the BJT switching...
Figure 3 Transistor amplifire circuit with source Vs and load R b) For the BJT switching circuit shown in Figure 4, i) Calculate the value of Ra so that the transistor is operating in saturation when switched on if the value of Rc is 3.9 kn. ii) What will the output voltage be for the applied input signal voltage shown if Vcet IS 0.2V? 5 V Re o V 5 V B 100 OV Figure 4 BUT switching circuit with...
IX With reference to the transistor amplifier shown in Figure QB4 below d For the bipolar transistor circuit of Figure QB4 the following DC bias conditions were measured: VB made. 1.6 V and VBE =0.6...
IX With reference to the transistor amplifier shown in Figure QB4 below d For the bipolar transistor circuit of Figure QB4 the following DC bias conditions were measured: VB made. 1.6 V and VBE =0.6 V. Detemine the value for RA, stating any assumptions e) Using these same conditions, calculate the current in Re and deduce the current in Rc, stating any assumptions made. Hence find the voltage across Rc and explain whether this voltage is suitable for this amplifier...
Can someone answer questions 8, 9 and 10 please, I really don't know how to solve it. interF Ex2c (SP2018).docx [Compatibility Mode) - Word TABLE TOOLS DESIGN PAGE LAYOUT REFERENCES MAILINGS REVI...
Can someone answer questions 8, 9 and 10 please, I really don't
know how to solve it.
interF Ex2c (SP2018).docx [Compatibility Mode) - Word TABLE TOOLS DESIGN PAGE LAYOUT REFERENCES MAILINGS REVIEW VIEW DESIGN LAYOUT 8) For the transistor circuit in figure, what is VcE when VIN-Ov? +10 V Re1.0 ko RB 9) what minimum value of 18 is required tosaturate this transistor if ocis 50? 10) Calculate the maximum value of Re when VIN-5V. 11) What command will pause...
Problem: In the circuit shown in Figure 1, Vee = 1.2 V, Vcc = 20 V,...
Problem: In the circuit shown in Figure 1, Vee = 1.2 V, Vcc = 20 V, Rp = 60 kN, Rc = 2 k. The input signal is a sinusoidal voltage given by Vin(t) = 0.2 sin(2000 ) V. The input and output characteristics of the transistor are provided on Page 2. (1) Find Ig, Ic and Vce. (30 points) Hint: Use the load line method. (Vor.) and (Vce: 1c) are the operating points of the transistor in the input...
1.(TCO 2) For the circuit in the following figure (Chapter 3, Figure 3-29, on page 135),...
1.(TCO 2) For the circuit in the following figure (Chapter 3,
Figure 3-29, on page 135), VCC=18
V, R1=10 K?, R2=2.2
K?, RC=1
k?, RE1=220
?,RE2=220 ?, RL=10
K?, Rs=1 K?VCC=18 V,
R1=10 K?, R2=2.2 K?, RC=1 k?, RE1=220
?,RE2=220 ?, RL=10 K?, Rs=1 K? . Determine
the AC voltage gain.
2.(TCO 2) For the circuit in the following figure (Chapter 3,
Figure 3-29, on page 135), VCC=18
V, R1=10 K?, R2=2.2
K?, RC=3
k?, RE1=220
?,RE2=220 ?, RL=5
K?, Rs=1 K?VCC=18 V,
R1=10 K?, R2=2.2 K?, RC=3 k?, RE1=220
?,RE2=220 ?, RL=5 K?, Rs=1 K?...
Please answer clearly 2. Consider the circuit shown in Figure 1. Determine values of Ri, R2, and Rc to provide the quie...
Please answer clearly
2. Consider the circuit shown in Figure 1. Determine values of Ri, R2, and Rc to provide the quiescent emitter current 1.5 mA and the quiescent collector to emitter voltage 5V. Assume β 100, Re-I㏀、Va= 200V, VBEon-0.7V, and VT= 25mV. R1 Rc Vcc に 10v R2 Re Figure 1: BJT biasing configuration
2. Consider the circuit shown in Figure 1. Determine values of Ri, R2, and Rc to provide the quiescent emitter current 1.5 mA and the...
Problem 5 Given the following circuit, assume the following parameters VBB IV, RB 220 k, RC...
Problem 5 Given the following circuit, assume the following parameters VBB IV, RB 220 k, RC = 2 k, VCC= 10 V, VBE(on)-0.7 V, and B 200 a) Calculate the base, collector, and emitter currents and the C-E voltage, also, calculate the transistor power dissipation b) What transistor configuration does the circuit resemble? Vcc=10V RC=2k Rg=220 kQ VCE VBB= 1V o + VRE IB
Problem 2 (15 points) In the circuit below, the transistor has B=50 and VEB = 0.7V....
Problem 2 (15 points) In the circuit below, the transistor has B=50 and VEB = 0.7V. Find the values of VB, VE, and Vc, and verify that the transistor is operating in the active mode. What is the largest value that Rc can have while the transistor remains in the active mode? +3V SR 3222 Vio R: 20 ks OV -
Could someone please help me on how I should be configuring the circuit in Figure 4(a)...
Could someone please help me on how I should be configuring the
circuit in Figure 4(a) in Multisim? Basically not understanding
question #1 in the Procedure. Cannot keep Vrb the same value while
adjusting Vcc. Then when trying to adjust Vbb to hold Vrb, Ib
changes.
Any help is appreciated!
Discrete Devices Section LAB 4 BJT CHARACTERISTICS AND BIASING Objective: The objective of this laboratory is to examine the operation of a bipolar junction transistor and plot its output characteristics...
1. For the transistor circuit shown in figure 1, what is: a. Vce when VIN = OV? b. What minimum value of IB is required to saturate the transistor if Boc is 200? c. Calculate the maximum value of Rs when Vin = 5V. VCC 10V RC 1.0 K RB Q1 VIN=0V 15C02MH-TLE GND Figure
Figure 3 Transistor amplifire circuit with source Vs and load R b) For the BJT switching circuit shown in Figure 4, i) Calculate the value of Ra so that the transistor is operating in saturation when switched on if the value of Rc is 3.9 kn. ii) What will the output voltage be for the applied input signal voltage shown if Vcet IS 0.2V? 5 V Re o V 5 V B 100 OV Figure 4 BUT switching circuit with...
IX With reference to the transistor amplifier shown in Figure QB4 below d For the bipolar transistor circuit of Figure QB4 the following DC bias conditions were measured: VB made. 1.6 V and VBE =0.6 V. Detemine the value for RA, stating any assumptions e) Using these same conditions, calculate the current in Re and deduce the current in Rc, stating any assumptions made. Hence find the voltage across Rc and explain whether this voltage is suitable for this amplifier...
Can someone answer questions 8, 9 and 10 please, I really don't
know how to solve it.
interF Ex2c (SP2018).docx [Compatibility Mode) - Word TABLE TOOLS DESIGN PAGE LAYOUT REFERENCES MAILINGS REVIEW VIEW DESIGN LAYOUT 8) For the transistor circuit in figure, what is VcE when VIN-Ov? +10 V Re1.0 ko RB 9) what minimum value of 18 is required tosaturate this transistor if ocis 50? 10) Calculate the maximum value of Re when VIN-5V. 11) What command will pause...
Problem: In the circuit shown in Figure 1, Vee = 1.2 V, Vcc = 20 V, Rp = 60 kN, Rc = 2 k. The input signal is a sinusoidal voltage given by Vin(t) = 0.2 sin(2000 ) V. The input and output characteristics of the transistor are provided on Page 2. (1) Find Ig, Ic and Vce. (30 points) Hint: Use the load line method. (Vor.) and (Vce: 1c) are the operating points of the transistor in the input...
1.(TCO 2) For the circuit in the following figure (Chapter 3,
Figure 3-29, on page 135), VCC=18
V, R1=10 K?, R2=2.2
K?, RC=1
k?, RE1=220
?,RE2=220 ?, RL=10
K?, Rs=1 K?VCC=18 V,
R1=10 K?, R2=2.2 K?, RC=1 k?, RE1=220
?,RE2=220 ?, RL=10 K?, Rs=1 K? . Determine
the AC voltage gain.
2.(TCO 2) For the circuit in the following figure (Chapter 3,
Figure 3-29, on page 135), VCC=18
V, R1=10 K?, R2=2.2
K?, RC=3
k?, RE1=220
?,RE2=220 ?, RL=5
K?, Rs=1 K?VCC=18 V,
R1=10 K?, R2=2.2 K?, RC=3 k?, RE1=220
?,RE2=220 ?, RL=5 K?, Rs=1 K?...
Please answer clearly
2. Consider the circuit shown in Figure 1. Determine values of Ri, R2, and Rc to provide the quiescent emitter current 1.5 mA and the quiescent collector to emitter voltage 5V. Assume β 100, Re-I㏀、Va= 200V, VBEon-0.7V, and VT= 25mV. R1 Rc Vcc に 10v R2 Re Figure 1: BJT biasing configuration
2. Consider the circuit shown in Figure 1. Determine values of Ri, R2, and Rc to provide the quiescent emitter current 1.5 mA and the...
Problem 5 Given the following circuit, assume the following parameters VBB IV, RB 220 k, RC = 2 k, VCC= 10 V, VBE(on)-0.7 V, and B 200 a) Calculate the base, collector, and emitter currents and the C-E voltage, also, calculate the transistor power dissipation b) What transistor configuration does the circuit resemble? Vcc=10V RC=2k Rg=220 kQ VCE VBB= 1V o + VRE IB
Problem 2 (15 points) In the circuit below, the transistor has B=50 and VEB = 0.7V. Find the values of VB, VE, and Vc, and verify that the transistor is operating in the active mode. What is the largest value that Rc can have while the transistor remains in the active mode? +3V SR 3222 Vio R: 20 ks OV -
Could someone please help me on how I should be configuring the
circuit in Figure 4(a) in Multisim? Basically not understanding
question #1 in the Procedure. Cannot keep Vrb the same value while
adjusting Vcc. Then when trying to adjust Vbb to hold Vrb, Ib
changes.
Any help is appreciated!
Discrete Devices Section LAB 4 BJT CHARACTERISTICS AND BIASING Objective: The objective of this laboratory is to examine the operation of a bipolar junction transistor and plot its output characteristics...
Most questions answered within 3 hours.
-
5. Discuss the use of fault tree analysis (FTA) for risk
assessment (maximum one paragraph).
asked 22 minutes ago -
Given that a sample of aluminium oxide has a Young's modulus of
393 GPa and a...
asked 1 hour ago -
At a certain temperature, the equilibrium constant, Kc, for this
reaction is 53.3.
H2(g)+I2(g)−⇀↽−2HI(g)Kc=53.3
At this...
asked 3 hours ago -
Question1 ) The STL provides similiar classes called stack and
queue, both of which gave functions...
asked 4 hours ago -
For Questions 1-4, assume you have 5 bits available:
1. For (positive) integers: What is the...
asked 4 hours ago -
convert grams into vloume with the density of water being at
.997514 g/cm^3 at 23.1 Celsuis...
asked 6 hours ago -
Foreman company obtained a $20,000, 6% loan on May 1, 2018.
Principal and interest will be...
asked 6 hours ago -
5. Problem 11.05 (Discounted Payback)
eBook
Project L costs $60,000, its expected cash inflows are $14,000
per...
asked 6 hours ago -
1. Which of the following is true about politics and health
organizations?
A. Health organizations are...
asked 7 hours ago -
A space vehicle is coasting at a constant velocity of 18.1 m/s
in the +y direction...
asked 8 hours ago -
5) Use the following balanced equation to answer questions
(a)-(i).
3 Cu(s) + 8 HNO3(aq) →...
asked 7 hours ago -
A three-year maturity bond with a 12% annual coupon rate is
currently traded at par $1000...
asked 8 hours ago