We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
In a three-phase system, two buses abc and a'b'c'are connected by two parallel lines Ll and...
solve no: 3.14 , 3.16, 3.19
please show each step and solve for beginners
120 Power System Analysis 3.12. A single-phase system similar to that shown in Figure 3.11 has two transformers A-B a B-C connected by a line B feeding a load at the receiving end C. The ratings and parame ter values of the components are 500 V/1.5 kV, 9.6 kVA. leakage reactance 5 % 1.2 kV/120 V, 7.2 kVA, leakage reactance 4 % series impedance (0.5 +...
Please help me to answer those question and answer with PHASOR
MAGNITUDE and PHASE ANGLE
Part 1:
Taking the rated power of generator G1 as the base power, and
the transformer T1 low-voltage
side rated voltage as the base voltage, calculate the Thevanin’s
equivalent zero-sequence
impedance, positive sequence impedance and the negative sequence
impedance viewed from
Bus-2. Specify your answers in per-unit.
Part 2:
Assuming the pre-fault bus voltages are at 1.02 pu, calculate the
fault currents in each phase...
The one line diagram of a three-phase power system is shown in
Fig.8. Impedances are marked in per unit on a 100 MW, 400 kV base.
The Load at Bus 2 is S2 = 15.93 MW - j33.4Mvar, and at Bus 3 is S3
= 77 MW + j14 Mvar. It is required to hold the voltage at Bus 3 at
400 kV, Angle 0 degs. Working in per unit, determine the voltages
at Buses 2 and 1.
Q8: The...
A single line diagram of a power system is shown in Fig. 2. The system data with equipment ratings and assumed sequence reactances are given the following table. The neutrals of the generator and A-Y transformers are solidly grounded. The motor neutral is grounded through a reactance Xn 0.05 per unit on the motor base. Assume that Pre-fault voltage is takin as VF-1.0 ,0° per unit and Pre- fault load current and Δ-Y transformer phase shift are neglected In the...
A synchronous generator with H = 3.5 is connected to an infinite bar through two lines with reactances of 0.40 each. The generator internal voltage is 1.2 pu and the operating voltage of the infinite bar is 1.0 pu. A three phase fault occurs on one of the lines between the generator and the infinite bar. The fault is eliminated by opening one of the lines. Determine the critical angle and time to eliminate the fault without losing stability.
A three-phase Yy0 connected transformer has a nominal rating of 250 kVA and a voltage ratio 15:0.4 kV. After conducting the short-circuit test, where the secondary winding is short-circuited, it is found that the primary series resistance is 0.08 pu and the primary series impedance magnitude is 0.1pu. The effect of the parallel branch in the transformer’s equivalent circuit may be neglected. Explain what information ‘Yy0’ gives about the transformer. Draw the per-phase equivalent circuit of the transformer during the...
Figure 1 shows a single-line diagram of a three phase, 60-Hz, synchronous generator, connected through a transformer and parallel transmission lines to an infinite bus. All reactances are given in per unit on a common system base. In steady state, the infinite bus receives 1.0 per unit real power at 0.95 power factor lagging. The generator in Figure 1 is initially operating in steady state, when circuit breaker B12 inadvertently opens. Use the equal area criterion to calculate the maximum...
A three-phase system is in "abc" sequence with a wye-connected load, and one phase voltage is given by ?AN = 60V?40° . What is the line voltage ?CA ?
ELE2601/101/3/2019 QUESTION 4 A 400 V three-phase, 50 Hz system, ABC sequence supplies the following loads: A star-connected load with the following phase impedances: A delta-connected load of equal phase impedances: Use VAB as reference and determine the following quantities: 4.1 The magnitude and angle of the currents drawn by the star-connected load (IAN; lBN; ICN). 4.1.1 The magnitude and angle of the phase (IAB; lBc; ICa) and line (lA; ls; Ic) currents drawn by the delta-connected load. 4.1.2 (12)...
4. (20 points) The three-phase Y-connected power supply has a line-to-neutral voltage KIN of 1.220° KV. A balanced-A load consisting of impedance Z1-20 30 Ω per phase is in parallel with a balanced-Y load having phase impedance of Z2 = 15245° Ω. Identical line impedances of Z1 = 3L15。Ω are in each of the three lines connecting the combined loads to the phase supply (a) Draw the per-phase equivalent circuit; (b) Find the line-to-line voltage Vab (magnitude and angle) at...