A process has a mean of 9 grams and a standard deviation of 0.25 grams. The lower spec limit is 8.00 grams and the upper spec limit is 10.00 grams.
- Compute Cp.
- What is the probability the process will operate within the specification limits?
- P{out of spec} for Wonderdisk
- μ = 10, σ = 2.3
qP{X ≤ 6 or X ≥ 12}
qP{8 ≤ X ≤ 13}
Answer:
NOTE:: I HOPE YOUR HAPPY WITH MY ANSWER....***PLEASE SUPPORT ME WITH YOUR RATING...
***PLEASE GIVE ME "LIKE"...ITS VERY IMPORTANT FOR ME NOW....PLEASE SUPPORT ME ....THANK YOU
A process has a mean of 9 grams and a standard deviation of 0.25 grams. The lower...
A key joint in a precision machining process has a lower specification limit of a width of 0.99 mm and an upper specification limit of 1.01 mm. The standard deviation is 0.005 mm and the mean is 1 mm. The company wants to reduce its defect probability and operate a "Six Sigma process." To what level would this company have to reduce the standard deviation in the process to meet this target? Note: A "Six Sigma process" has a process...
Product filling weights are normally distributed with a mean of 365 grams and a standard deviation of 19 grams. a. Compute the chart upper control limit and lower control limit for this process if samples of size 10, 20 and 30 are used (to 2 decimals). Use Table 19.3. For samples of size 10 UCL =| LCL For a sample size of 20 UCL = LCL For a sample size of 30 UCL = LCL = b. What happens to...
Given an upper specification limit of 40, a lower specification limit of 25, mean process performance of 30, and a process standard deviation of 3: a. Calculate Cp b. Calculate Cpk c. Is the process performance acceptable – if not, why? d. To identify factors targeting process improvement the design should be set up to explore factors affecting both process mean and process __________________ .
For a key joint, a precision machining process has a lower specification limit of a width of 0.99 mm and an upper specification limit of 1.01 mm. The standard deviation is 0.005 mm and the mean is 1 mm. (a) What is the process capability index for the bottle filling process? (Round the answer to 3 decimal places.) (b) The company now wants to reduce its defect probability and operate a “six sigma process.” To what level would they have...
A certain process is under statistical control and has a mean value of 130 and a standard deviation of 8. The specifications for the process are: a. USL (upper specification limit) = 150 b. LSL(lower specification limit) =100 a. Calculate the cp and cpk b. Which of these indices is a better measure of process capability and why? c. Assuminng a normal distribution what percentage of output is expected to fall ourside the specification. Why is it important to know...
Consider a normally distributed population with mean µ = 75 and standard deviation σ = 11. a. Calculate the centerline, the upper control limit (UCL), and the lower control limit (LCL) for the x¯x¯ chart if samples of size 6 are used. (Round the value for the centerline to the nearest whole number and the values for the UCL and LCL to 2 decimal places.) centerline upper control limit lower control limit b. Calculate the centerline, the upper control...
C&A’s potato chip filling process has a lower specification limit of 9.5 oz. and an upper specification limit of 10.5 oz. The standard deviation is 0.3 oz. and the mean is 10 oz. What is the probability that a bag will weigh more than 10.5 oz.? 95.2% 90.4% 9.56% 4.78%
Lean Six Sigma The Lower Specification Limit is 8.0 seconds 36. Representative data gathered from a process that follows a normal distribution shows a mean of 8.2 seconds with a standard deviation of 0.3 seconds. The process has 8.5 seconds as an upper specification limit. What is the process yield? a. Calculate: Cp and Cpk b. How many defects per million opportunities the process produces? (hint: use the Excel spreadsheet given in class) c. What is the Sigma of the...
value: 10.00 points Consider a normally distributed population with mean ?-112 and standard deviation ?-22. a. Calculate the centerline, the upper control limit (UCL), and the lower control limit (LCL) for the X chart if samples of size 6 are used. (Round the value for the centerline to the nearest whole number and the values for the UCL and LCL to 2 decimal places.) Centerline Upper Control Limit Lower Control Limit 112 b. Calculate the centerline, the upper control limit...
An industrial sewing machine uses ball bearings that are targeted to have a diameter of 0.73 inch. The lower and upper specification limits under which the ball bearing can operate are 0.72 inch (lower) and 0.74 inch (upper). Past experience has indicated that the actual diameter of the ball bearings is approximately normally distributed, with a mean of 0.732 inch and a standard deviation of 0.006 inch. Suppose a random sample of 21 ball bearings are selected. Complete parts (a)...