2.Design a high pass filter with a -3 dB frequency of 1 MHz, using the same parts in problem #1.
Sketch the magnitude and phase of the transfer function.
Answer Qs 2 only I put 1 for the reference
1.Design a low pass filter with a – 3 dB frequency is 1 MHz. The largest capacitor that I have in my bin is 10 nF.
a. Find the transfer function for the circuit and sketch its magnitude and phase that you expect to see.
b. Run a QUCS simulation to verify your estimate. (Prove to me that you’re practicing safe simulation)
We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
2.Design a high pass filter with a -3 dB frequency of 1 MHz, using the same...
13.6 Design a first-order active high-pass filter with a response of +12 dB in the high-frequency limit and -20 dB at 1.2 kHz. Let C 1 nF 13.6 Design a first-order active high-pass filter with a response of +12 dB in the high-frequency limit and -20 dB at 1.2 kHz. Let C 1 nF
For the low-pass filter circuit shown in Fig 2 3k Ω 200mil in out Fig 2 3.a. Use a 2.2nF capacitor to design a high-pass filter to have a cutoff frequency of Skn Draw a schematic of your design. Show all component values and voltages c. Sketch the frequency response of the voltage gain and phase shift Magnitude dB Frequency Hz Phase Frequency Hz For the low-pass filter circuit shown in Fig 2 3k Ω 200mil in out Fig 2...
1. By using an analog filter with a Butterworth response of order 3, design a digital IIR low pass filter with 3-db cutoff frequency 2c 0.6TT a) b) c) Evaluate the transfer function of the analog filter (10marks) Skecth the block diagram of transfer function (5 marks) Plot the magnitude response of the filters. (5marks) 1. By using an analog filter with a Butterworth response of order 3, design a digital IIR low pass filter with 3-db cutoff frequency 2c...
Using the windowing function discussed in class, design a band pass FIR filter centered at 20 MHz with bandwidth 30MHz.. 3. Using the windowing functions discussed in class, design a band-pass FIR filter centered at 20 MHz with a bandwidth 30 MHz (), a minimum stop band attenuation of 30 dB, and a transition width of 1 MHz. The sampling frequency is 80 MHz, 3. Using the windowing functions discussed in class, design a band-pass FIR filter centered at 20...
Using the windowing functions discussed in class, design a low-pass FIR filter with a cutoff frequency of 2 kHz, a minimum stop band attenuation of 40 dB, and a transition width of 200Hz. The sampling frequency is 10kHz. 1. Using the windowing functions discussed in class, design a low-pass FIR filter with a cutoff frequency of 2 kHz, a minimum stop band attenuation of 40 dB, and a transition width of 200 Hz. The sampling frequency is 10 kHz 2....
(a) Design a first–order high-pass filter with a cutoff frequency fc = 1.5 kHz and a passband gain |Ao| = 20dB, using a capacitor C = 47nF. Include a compensation resistor and determine its value. (b) Sketch the frequency response for the circuit (i.e., magnitude vs. frequency and phase vs. frequency). On the magnitude response plot, indicate the cutoff frequency, bandpass gain, and bandstop rolloff slope. On the phase response plot, indicate the approximate value of the phase angle at...
12. Design a fourth order, 2 dB Chebyshev highpass filter with a cutoff frequency of 2.4 kHz a. Draw the circuit, labeling Vin, Yout, and all component values. (14 points) and a passband gain of 0 dB. Use capacitor values of 3300 pF an approximation of the Bode plot of the magnitude transfer function IH(ia) in dB, İndicating the ripple, the cutoff frequency, and the approximate filter roll-off in dB/decade. Note, this does not reguire solving for the function. (6...
Active Low-pass and High-pass Filters for Crossover Circuitry (PSPICE) Design a first order active high-pass filter with cut-off frequency of 1 kHz & gain 20dB. Design a first order active low-pass filter with cut-off frequency of 1 kHz & gain 20dB. Plot the magnitude and phase responses of the active high-pass and low-pass filters you have designed using PSpice (Use UA741 Op amp and ±12V dual supply). Connect your active low-pass and high-pass filters as shown in Fig. 1-b. Assume...
(a) Design a first order active low pass filter with a corner frequency of 1 kHz and a normalized transfer function of 1/(s + 1.96523). You may assume C = 10 nF.
QI (a) () Design an active filter using non-inverting amplifier that will produce a frequency response as shown in Figure Ql(a). The bandwidth of the filter is 30 kHz. Use a capacitor value of 10 nF. (9 marks) Draw the circuit and clearly label it. (5 marks) (b) Derive the transfer function of the filter in Q1(b). (6 marks) Av (dB) 28 dB 25 dB - 20 dB/decade + 20 dB/decade - 1 1 35 kHz 40 kHz Figure Qi(a)...