For the low-pass filter circuit shown in Fig 2 3k Ω 200mil in out Fig 2 3.a. Use a 2.2nF capacitor to design a high-pas...
For the low-pass filter circuit shown in Fig 2 200mH 3k Ω out in Fig 2 (i) (ii) (iii) Write an expression for the transfer function of the circuit State the value of the dc gain of the filter circuit in dB Calculate the cutoff frequency of the filter b. Sketch the frequency response of the voltage gain and phase shift for the filter shown in Fig 2. Show all the values and required information in both graphs Magnitude Frequency...
10 Design a low pass filter using a resistor R and a capacitor C of 0.2uF. Sketch the circuit diagram, mark thoe output voltage Vo, calculate the resistance value for R if 3dB frequency is 2500 Hz, and write out the voltage gain vs ω (for both magnitude and phase). Repeat the design if R is given as 30 Ohm and C is unknown.
please show all steps and matlab plot , 5) Design a one-pole, one-zero passive filter to have a low-frequency gain of -32 dB, a high-frequency gain of 0 dB, and a cutoff frequency of 2,000 Hz. Specify the circuit and all component values. Use Matlab to plot the magnitude and phase frequency response for your filter. 5) Design a one-pole, one-zero passive filter to have a low-frequency gain of -32 dB, a high-frequency gain of 0 dB, and a cutoff...
Active Low-pass and High-pass Filters for Crossover Circuitry (PSPICE) Design a first order active high-pass filter with cut-off frequency of 1 kHz & gain 20dB. Design a first order active low-pass filter with cut-off frequency of 1 kHz & gain 20dB. Plot the magnitude and phase responses of the active high-pass and low-pass filters you have designed using PSpice (Use UA741 Op amp and ±12V dual supply). Connect your active low-pass and high-pass filters as shown in Fig. 1-b. Assume...
Design a low pass filter with a cutoff frequency of 1 kHz +/- 100 Hz and a gain of 16.0 dB +/- 1.0 dB in the passband. The R2 and C components of the filter control the cutoff frequency, and are inversely proportional to the cutoff frequency. So decreasing the resistance or capacitance will increase the cutoff frequency. The R1 and Rf components determine the gain of the amplifier. Increasing the value of Rf will increase the gain. Increasing the...
2.Design a high pass filter with a -3 dB frequency of 1 MHz, using the same parts in problem #1. Sketch the magnitude and phase of the transfer function. Answer Qs 2 only I put 1 for the reference 1.Design a low pass filter with a – 3 dB frequency is 1 MHz. The largest capacitor that I have in my bin is 10 nF. a. Find the transfer function for the circuit and sketch its magnitude and phase that...
(a) Design a first–order high-pass filter with a cutoff frequency fc = 1.5 kHz and a passband gain |Ao| = 20dB, using a capacitor C = 47nF. Include a compensation resistor and determine its value. (b) Sketch the frequency response for the circuit (i.e., magnitude vs. frequency and phase vs. frequency). On the magnitude response plot, indicate the cutoff frequency, bandpass gain, and bandstop rolloff slope. On the phase response plot, indicate the approximate value of the phase angle at...
CIRCUIT ANALYSIS 2. Design a second order high pass filter with a passband gain of 20 dB, and a 3 dB upper cutoff frequency ofS Hz.[D] (40)
200 HZ. 6.25) Design a cascading LC low-pass filter with maxi- mally flat magnitude response. Use a passband of 0 to 5 kHz with 5 kHz cutoff frequency and filter to attenuate all frequencies at and above 10 kHz by at least 30 dB. Use R R1 = 50 2 200 HZ. 6.25) Design a cascading LC low-pass filter with maxi- mally flat magnitude response. Use a passband of 0 to 5 kHz with 5 kHz cutoff frequency and filter...
design an active low pass filter with cutoff frequency of 400 hz and gain of 10 db at dc