200 HZ. 6.25) Design a cascading LC low-pass filter with maxi- mally flat magnitude response. Use a passband of 0 to...
Design a low pass filter with a cutoff frequency of 1 kHz +/- 100 Hz and a gain of 16.0 dB +/- 1.0 dB in the passband. The R2 and C components of the filter control the cutoff frequency, and are inversely proportional to the cutoff frequency. So decreasing the resistance or capacitance will increase the cutoff frequency. The R1 and Rf components determine the gain of the amplifier. Increasing the value of Rf will increase the gain. Increasing the...
Using the windowing functions discussed in class, design a low-pass FIR filter with a cutoff frequency of 2 kHz, a minimum stop band attenuation of 40 dB, and a transition width of 200Hz. The sampling frequency is 10kHz. 1. Using the windowing functions discussed in class, design a low-pass FIR filter with a cutoff frequency of 2 kHz, a minimum stop band attenuation of 40 dB, and a transition width of 200 Hz. The sampling frequency is 10 kHz 2....
For the low-pass filter circuit shown in Fig 2 3k Ω 200mil in out Fig 2 3.a. Use a 2.2nF capacitor to design a high-pass filter to have a cutoff frequency of Skn Draw a schematic of your design. Show all component values and voltages c. Sketch the frequency response of the voltage gain and phase shift Magnitude dB Frequency Hz Phase Frequency Hz For the low-pass filter circuit shown in Fig 2 3k Ω 200mil in out Fig 2...
CIRCUIT ANALYSIS 2. Design a second order high pass filter with a passband gain of 20 dB, and a 3 dB upper cutoff frequency ofS Hz.[D] (40)
design an active low pass filter with cutoff frequency of 400 hz and gain of 10 db at dc
Design a second-order Butterworth low-pass filter to satisfy the specifications a. The dc gain is unity (zero dB); b. The gain is no smaller than -1 dB for frequencies between 0 and 2,000 Hz; and c. The gain is no larger than -40 dB for frequencies larger than 40 kHz. Determine a circuit realization as a series RLC low-pass filter. Pick reasonable values of R, L, and C. Design a second-order Butterworth low-pass filter to satisfy the specifications a. The...
Problem 3) (15 points) An RC filter is designed with a cutoff frequency of 100 Hz. If a low-pass first order filter is used, determine the attenuation (Attenuation %, and Attenuation(dB)) of the filtered analog signal at 50, 75 and 200 Hz. (use k -1) o Determine the order of the filter if magnitude ratio of <0.01 is needed at 200 Hz. Problem 3) (15 points) An RC filter is designed with a cutoff frequency of 100 Hz. If a...
1. By using an analog filter with a Butterworth response of order 3, design a digital IIR low pass filter with 3-db cutoff frequency 2c 0.6TT a) b) c) Evaluate the transfer function of the analog filter (10marks) Skecth the block diagram of transfer function (5 marks) Plot the magnitude response of the filters. (5marks) 1. By using an analog filter with a Butterworth response of order 3, design a digital IIR low pass filter with 3-db cutoff frequency 2c...
Design a low-pass filter (LPF) has pass-band frequency fP = 100 kHz, maximum attenuation in passband Amax = 2 dB, stop-band frequency fS = 120 kHz, minimum attenuation in stop-band Amin = 60 dB. a/ Calculate the minimum order N for Chebyshev filter and the corresponding minimum stop-band attenuation? b/ Calculate the minimum order N of low-pass B
show and explain all work 165. Draw the magnitude response of an ideal high pass filter with stop-band cutoff of 100iz and and cutoff of 200Hz and a Nyquist frequency of 1kHz. What is the roll-off of this filter pass-b measured in dB per Hz did you choose in your example? 165. Draw the magnitude response of an ideal high pass filter with stop-band cutoff of 100iz and and cutoff of 200Hz and a Nyquist frequency of 1kHz. What is...