Find Vout, as well as the minimum and maximum Vx values that keep the amplifier out of saturation.
Find Vout, as well as the minimum and maximum Vx values that keep the amplifier out...
For the circuit shown below, design the values of R1 and R2 that will cause Vout-6 Vif VIv-9 V. If the resistors you chose have a tolerance of 1 %, what is the maximum and minimum values of Vout? Design R3 so that the LED will be properly lit, if IF=10 mA, VF-3 V and Vout-6 V Design equations from the data sheet: VOUT-1.25%(1+R2 R1) U1 OUT ININLT OUT R3 R1 V1 (R3) R1) ADJ LT317A D1 IN) R2 (R2)...
Solve symbolically.
1.(4) With the following values, determine output voltage Vout for the following amplifier circuit. Vin= Rin= R = - FOTO Vin to Vout
Help please
Problem 4- Common Source Amplifier: For the circuit in Fig. 4, draw the small signal equivalent circuit and find the following small signal values: gm , go, Vout/Vin , Rout and Rin You can assume that the overdrive voltage for the transistor is 0.2V and 2 for the NMOS and PMOS are 0.1V1 and 0.05V-1 respectively.. The drain source current of the transistor is 200uA Vee 9v 4ook 2 Vin Pmos C 5ook 16.Sk Fig. 4
Problem 4-...
For the following circuits, find out the type of the amplifier, the voltage gain, Av, and its related input resistance, rin and output resistance rout- M1 B1 M1 M2 M1 IN B1 rout rout VOUT VOUT VOUT rout Q3 Q2 B1 VIN VIN M1 Vai B1 M1 B1 M2 VOUT rin VOUT Q2 VIN Q3
For the following circuits, find out the type of the amplifier, the voltage gain, Av, and its related input resistance, rin and output resistance rout-...
You are required to design a 2-stage voltage amplifier (find
values for RE, RC1, RC2) to meet the following criteria: an input
resistance of 400 kΩ and an overall voltage gain equal to or
greater than 250, with a resistor output load, RL. Use a
common-emitter with emitter degradation (RE) stage for the input,
followed by a commonemitter amplifier with bias current equal to
0.5 mA. (VCC = 20 V, βo = 200 and the DC levels of the first...
QUESTION 3 Given the following circuit for an INA121 instrumental amplifier. What is Vout in terms of V1 and V2? RG_01 FI Vout REF RG AD8421 5V o A. Vous = 10(V2-V1) o B. Vout =(V2-V1) o C. Vour = 3(V2-V1) O D. Vour = 2(V2 - 12) QUESTION 4 Which value of Rc for the INA121 instrumental amplifier would you have the best measurement for Rsense in the following circuit. 5V Rlimit RG01 Rsense RG Vsense REF RGAD8421 1N4148...
4) Consider the MOSFET differential amplifier shown below, with Io-2 mA, and RL- 10 kS2, Rss-100 k2, VDD- +8V and Vss--8V. The NMOS transistors in the circuit are nominally identical, with kn 2 mA/V2, VTn 1.0 V and ro 100 k2. The PMoS transistors in the circuit are nominally identical, with kp 2 mA/V2, [VTpl 1.0 V and ro 100 kΩ M3 M4 0 M1 M2 a) First consider the DC bias point. Assuming that the current mirror requires at...
5) Problem 5: For the circuit in Figure 4, use the same PMOS and NMOS data given in the 4th question. Assume Ibias-50uA ; all L = 0.5um; VDD = 3V: W,-25um; W2= 75um ; VIN 2V Find Va, Vovs, I2, VovI; Wi to carry 12 (current) in saturation, the maximum and minimum values of VouT to keep MI and M2 in saturation. biAs Nmos M3 CAND Figure 4
9.6 Maximum and Minimum Values Find the local maximum, minimum, and saddle points of the following functions. f(x,y) = ycost f(x,y) - * (x2 - y2)
3. Consider the following multistage amplifier. The current source values are 1, -2mA, I, - 1mA, and 1 - 1mA. Also, Voo - Vss - 6V. +VDD (a) If the DC voltage at the output is OV, find all DC currents at the drains of all transistors. Also, find the DC voltages at the drain, gate, and source terminals for all transistors (you can put the values directly on the figure). Use k.(W/L) - k.(W/L) = 2mA/V. And Vin -...