Need solution 100%right....make sure about steps... Solution should be step by step
Homework Answers
Add Answer to:
Need solution 100%right....make sure about steps...
Solution should be step by step
(a) Explain why the...
4. A T-shaped cross-sectional beam is loaded as shown in the figure. Determine the following a....
4. A T-shaped cross-sectional beam is loaded as shown in the figure. Determine the following a. Sketch the internal shear force and bending moment diagrams for the beam. b. Calculate the maximum magnitude of the bending stress. Indicate where this occurs on the cross-section and along the length of the beam. c. Calculate the transverse shearing stress at the centroid of the cross-section using the maximum magnitude of the transverse shear force. - 200 mm 8 KN 1.5 kN/m 20...
If the beam is subjected to a positive bending moment of M = 100 kN-m, determine...
If the beam is subjected to a positive bending moment of M = 100 kN-m, determine the maximum and minimum bending stress. Also determine the shear stress at point, A which is 50 mm above from the bottom. The cross-section of the beam is I-shaped and shown in the figure. 300 mm 30 mm 300 mm . 50 mm 30 mm
If the beam is subjected to a positive bending moment of M = 100 kN-m, determine...
If the beam is subjected to a positive bending moment of M = 100 kN-m, determine the maximum and minimum bending stress. Also determine the shear stress at point, A which is 50 mm above from the bottom. The cross-section of the beam is I-shaped and shown in the figure. 300 mm 30 mm 300 mm . 50 mm 30 mm
Dimensions for beam section (mm) ( B1= 20 ,B2= 40, D=50 ,T1=4 ,T2=6 ) Beam span...
Dimensions for beam section (mm)
( B1= 20 ,B2= 40, D=50 ,T1=4 ,T2=6 )
Beam span L (m) =4
Uniform Load w (kN/ m) =8
i have anly 20 min
Q1 The cross-section of a cantilever beam is given in the figure. Determine the maximum value of transverse shear stress if the beam carries a uniform load of w kN/m on the entire span L. T2 T1 B2 (All dimensions in mm)
For the beam shown below, find the maximum bending stress and maximum transverse shear stress. That...
For the beam shown below, find the maximum bending stress and maximum transverse shear stress. That is, carry out load and stress analyses in the following order. Load Analysis Draw the load diagram or free body diagram (FBD) and determine the support reactions. Show your calculations. • Draw the shear force diagram (SFD). Show your calculations. Draw the bending moment diagram (BMD). Show your calculations. Stress Analysis Identify the critical section(s) and determine the maximum normal (bending) stress at the...
The beam shown in Figure 1 has a clear span length of L = 7.6 m...
The beam shown in Figure 1 has a clear span length of L = 7.6 m and x : 1.5 m. The beam cross section is shown in Figure 2 and supports the following loads: WL = 30 kN/m. Wb = 50 kN/m, Q.-50 kN, QD = 80 kN, and supports its own weight. Assume f,'-25 MPa,.-420 MPa, b-350 mm. d-702 mm, h 750 mm, colinn width-450 1. Calculate the beam own weight 2. Calculate the ultimate loads applied on...
PLEASE PRINT Question Four The beam has a cross section shown below and is subjected to...
PLEASE PRINT
Question Four The beam has a cross section shown below and is subjected to a 1 kN load as shown. The beam AB has a length of 3 m. a) Draw the shear force and bending moment diagrams. b) Determine the maximum bending stress. c) Where is the location of the maximum stress in b) above? 30 mm 30 mm 30 mm 50 mm t 40 mm 50 m 40mm
Two timber beams are mounted at right angles and in contact with each other at their...
Two timber beams are mounted at right angles and in contact with each other at their midpoints. the upper beam A is 50 mm wide by 200 mm deep ans simply supported on an 3 m span; the lower beam B is 80 mm wide by 200 mm deep and simply supported on a 4 m span. At their cross-over point, they jointly support a load P = 10 kN. Determine the maximum normal stress in each beam.
3. A beam with a hollow circular cross section of outer diameter D and inner diameter...
3. A beam with a hollow circular cross section of outer diameter D and inner diameter d. The length Lis fixed at a wall. Consider the following loading conditions, all applied to the beam at the midpoint of length L. For each loading scheme state determine the magnitude of that stress in terms of the variables given in the problem). (5 points) i. ii. iii. iv. V. Normal stress due to axial load F Shear stress due to torque T...
NEAT HANDWRITING AND SHOW ALL STEPS PLEASE Problem 2: (50 points) The beam has a rectangular...
NEAT HANDWRITING AND SHOW ALL STEPS PLEASE
Problem 2: (50 points) The beam has a rectangular cross section as shown below. If the intensity of the distributed load w=800N/m, Determine: a) The absolute maximum shear stress and its location. b) The maximum compressive stress and its location. 50 mm V | 150 mm 2m + 2m + 2m
4. A T-shaped cross-sectional beam is loaded as shown in the figure. Determine the following a. Sketch the internal shear force and bending moment diagrams for the beam. b. Calculate the maximum magnitude of the bending stress. Indicate where this occurs on the cross-section and along the length of the beam. c. Calculate the transverse shearing stress at the centroid of the cross-section using the maximum magnitude of the transverse shear force. - 200 mm 8 KN 1.5 kN/m 20...
If the beam is subjected to a positive bending moment of M = 100 kN-m, determine the maximum and minimum bending stress. Also determine the shear stress at point, A which is 50 mm above from the bottom. The cross-section of the beam is I-shaped and shown in the figure. 300 mm 30 mm 300 mm . 50 mm 30 mm
If the beam is subjected to a positive bending moment of M = 100 kN-m, determine the maximum and minimum bending stress. Also determine the shear stress at point, A which is 50 mm above from the bottom. The cross-section of the beam is I-shaped and shown in the figure. 300 mm 30 mm 300 mm . 50 mm 30 mm
Dimensions for beam section (mm)
( B1= 20 ,B2= 40, D=50 ,T1=4 ,T2=6 )
Beam span L (m) =4
Uniform Load w (kN/ m) =8
i have anly 20 min
Q1 The cross-section of a cantilever beam is given in the figure. Determine the maximum value of transverse shear stress if the beam carries a uniform load of w kN/m on the entire span L. T2 T1 B2 (All dimensions in mm)
For the beam shown below, find the maximum bending stress and maximum transverse shear stress. That is, carry out load and stress analyses in the following order. Load Analysis Draw the load diagram or free body diagram (FBD) and determine the support reactions. Show your calculations. • Draw the shear force diagram (SFD). Show your calculations. Draw the bending moment diagram (BMD). Show your calculations. Stress Analysis Identify the critical section(s) and determine the maximum normal (bending) stress at the...
The beam shown in Figure 1 has a clear span length of L = 7.6 m and x : 1.5 m. The beam cross section is shown in Figure 2 and supports the following loads: WL = 30 kN/m. Wb = 50 kN/m, Q.-50 kN, QD = 80 kN, and supports its own weight. Assume f,'-25 MPa,.-420 MPa, b-350 mm. d-702 mm, h 750 mm, colinn width-450 1. Calculate the beam own weight 2. Calculate the ultimate loads applied on...
PLEASE PRINT
Question Four The beam has a cross section shown below and is subjected to a 1 kN load as shown. The beam AB has a length of 3 m. a) Draw the shear force and bending moment diagrams. b) Determine the maximum bending stress. c) Where is the location of the maximum stress in b) above? 30 mm 30 mm 30 mm 50 mm t 40 mm 50 m 40mm
3. A beam with a hollow circular cross section of outer diameter D and inner diameter d. The length Lis fixed at a wall. Consider the following loading conditions, all applied to the beam at the midpoint of length L. For each loading scheme state determine the magnitude of that stress in terms of the variables given in the problem). (5 points) i. ii. iii. iv. V. Normal stress due to axial load F Shear stress due to torque T...
NEAT HANDWRITING AND SHOW ALL STEPS PLEASE
Problem 2: (50 points) The beam has a rectangular cross section as shown below. If the intensity of the distributed load w=800N/m, Determine: a) The absolute maximum shear stress and its location. b) The maximum compressive stress and its location. 50 mm V | 150 mm 2m + 2m + 2m
Most questions answered within 3 hours.
-
Suppose that on a temperature scale X, water boils at 203.0°X
and freezes at -105.7°X. What...
asked 30 minutes ago -
BaS crystallizes in a cubic unit cell with S2- ions on each
corner and each face....
asked 1 hour ago -
A. 0≤P(Oi)≤10≤P(Oi)≤1 for each i
B. P(Oi)≤0P(Oi)≤0
C. P(Oi)=1+P(OCi)P(Oi)=1+P(OiC)
D. P(Oi)≥1P(Oi)≥1
If an experiment consists of...
asked 2 hours ago -
A battery has an emf of 9.20V and an internal resistance of 1.20
ohm. a)What resistance...
asked 2 hours ago -
The area of an elastic circular loop decreases at a constant
rate, dA/dt = −6.60×10−3 m2/s...
asked 3 hours ago -
The denaturation of proteins can be described by the
equilibrium
F⇌U
where F and U represent...
asked 5 hours ago -
Please answer what the maximum and minimum force is, and the
angle on the ion is...
asked 5 hours ago -
implement a program that reads a number of rows and a symbol.
The program will draw...
asked 5 hours ago -
Assume that when adults with smartphones are randomly selected,
45% use them in meetings or classes....
asked 5 hours ago -
Determine the number of formula units of
Na2SO4 and moles of oxygen contained in 8.11
moles...
asked 5 hours ago -
Explain in steps on the following code
What would be the output when executed
using System;...
asked 5 hours ago -
Given the information in the table, which of the following
statements is CORRECT?
Stock A
Stock...
asked 5 hours ago