Homework Answers
Add Answer to:
DESIGN PROBLEM MULTISIN 14.20 Use a 5 nF capacitor to design a series RLC band- pass...
Problem 4 Use a 5 nF capacitor to design a series RLC bandpass filter. The center...
Problem 4 Use a 5 nF capacitor to design a series RLC bandpass filter. The center frequency the filter is 8 kHz, and the quality factor is 1.5. Part A Specify the value of L. View Available Hint(s) EVO AQH vec ? L = 0.079 ml Submit Previous Answers * Incorrect; Try Again; 8 attempts remaining Part B Specify the value of R. 10 AEDIf vec ? R = k12 Submit Request Answer Problem 4 Use a 5 nF capacitor...
answer fast 2- Design an RLC Band Reject filter with a lower cutoff frequency of 2...
answer fast
2- Design an RLC Band Reject filter with a lower cutoff frequency of 2 kHz and an upper cutoff frequency of 2.1 kHz. Consider a capacitor C = 3.7nF and calculate L, C, and Q. a) Give the Transfer function of this filter. b) Find the central frequency f., the bandwidth (BW) in Hz, and the quality factor (Q). c) Sketch the frequency response of this filter only magnitude.
Design a parallel RLC band-pass filter to have the nominal center frequency f0 = 280 kHz and the 3dB bandwidth B = 7.9 k...
Design a parallel RLC band-pass filter to have the nominal center frequency f0 = 280 kHz and the 3dB bandwidth B = 7.9 kHz. Use only single, standard-valued components: 5% resistors, 10% capacitors and 10% IMS-5WD-40 inductors. Assume that inductor's Q is constant in the frequency range [0.1 - 1.0]ft, where ft is the 'TEST FREQUENCY Q' given in the IMS-5WD-40 data sheet. L = C = R =
pls i want as fast as possible Q4 (20 pts) Design a series RLC band pass...
pls i want as fast as possible
Q4 (20 pts) Design a series RLC band pass filter as shown below, with low frequency cut-off at W = 100 rad/sec and high frequency cut-off at WH=10 krad /sec. (4 pts) a) Determine the center frequency wo and the bandwidth B (10 pts) b) Choose L-100 mH and calculate the values of R and C (6 pts) c) Find the magnitude of H(jw)= Vo / V, and evaluate it at www с...
Homework #2 Problem 14.38 PSpice Multisim Part A Consider the bandreject filter shown in (Figure 1)....
Homework #2 Problem 14.38 PSpice Multisim Part A Consider the bandreject filter shown in (Figure 1). Suppose that R-4 k2,L-3.5 mH, C-62.5 nF Calculate the center frequency wo. Express your answer using three significant figures vec krad/s Figure 1 of 1 Submit Request Answen Part B Calculate the center frequency f, in kilohertz. Express your answer using three significant figures vec kHz Problem 14.38 PSpice Multisim Part C Consider the bandreject filter shown in (Figure 1). Suppose that R-4 k2,L-3.5...
5) Consider the following second-order bandpass filter. As input voltage, apply V(t) 100Ω, C-4.7 μF. and L-10mH. sin(wt).R in Vout Fig 9: Second-order band-pass filter a) Determine the frequenc...
5) Consider the following second-order bandpass filter. As input voltage, apply V(t) 100Ω, C-4.7 μF. and L-10mH. sin(wt).R in Vout Fig 9: Second-order band-pass filter a) Determine the frequency response function H(ju) Ve-ju) / Vm(ju) and sketch the magnitude and phase characteristics versus w by calaulation. Calculate the theoretical cutoff frequency of the filter Using PSpice AC analysis, plot magnitude lHju)l and phase ф characteristics of the filter, between 1 Hz-100 KHz b) c)
5) Consider the following second-order bandpass...
C V. Figure 2 A band-pass filter circuit This is the transfer function of a band-pass...
C V. Figure 2 A band-pass filter circuit This is the transfer function of a band-pass filter having R = R2 //R Center frequency, a[ 1/R' R C12 radians Bandwidth B2(R, C) radians Maximum Gain Ag- R/2R Band-Pass Filter Design Design a band-pass filter to obtain f-160 Hz, B-16 Hz and o- 10. Supply voltages of +20 and -20 Volts are available. Laboratory Measurements and Results . By applying sinusoidal voltage at the input and by varying its frequency, obtain...
Problem 2 a) Using 5 nF capacitors, design an active broad- band first-order bandreject filter with...
Problem 2 a) Using 5 nF capacitors, design an active broad- band first-order bandreject filter with a lower cutoff frequency of 1000 Hz, an upper cut-off frequency of 5000 Hz, and a pass band gain of 10dB. b) Draw the schematic diagram of the filter. c) Write the transfer function to find H(jωo), where ωo is the center frequency of the filter. d) What is the gain (in decibels) of the filer at the center frequency? e) Using Matlab make...
200 HZ. 6.25) Design a cascading LC low-pass filter with maxi- mally flat magnitude response. Use a passband of 0 to...
200 HZ. 6.25) Design a cascading LC low-pass filter with maxi- mally flat magnitude response. Use a passband of 0 to 5 kHz with 5 kHz cutoff frequency and filter to attenuate all frequencies at and above 10 kHz by at least 30 dB. Use R R1 = 50 2
200 HZ. 6.25) Design a cascading LC low-pass filter with maxi- mally flat magnitude response. Use a passband of 0 to 5 kHz with 5 kHz cutoff frequency and filter...
1. Design the following series RLC filter (find values of R and L) with a quality...
1. Design the following series RLC filter (find values of R and L) with a quality factor of 5 and a center frequency of 20 krad / s. For the filter that you designed, find the bandwidth and the values of two cutoff frequencies 0.05 HF L
Problem 4 Use a 5 nF capacitor to design a series RLC bandpass filter. The center frequency the filter is 8 kHz, and the quality factor is 1.5. Part A Specify the value of L. View Available Hint(s) EVO AQH vec ? L = 0.079 ml Submit Previous Answers * Incorrect; Try Again; 8 attempts remaining Part B Specify the value of R. 10 AEDIf vec ? R = k12 Submit Request Answer Problem 4 Use a 5 nF capacitor...
answer fast
2- Design an RLC Band Reject filter with a lower cutoff frequency of 2 kHz and an upper cutoff frequency of 2.1 kHz. Consider a capacitor C = 3.7nF and calculate L, C, and Q. a) Give the Transfer function of this filter. b) Find the central frequency f., the bandwidth (BW) in Hz, and the quality factor (Q). c) Sketch the frequency response of this filter only magnitude.
pls i want as fast as possible
Q4 (20 pts) Design a series RLC band pass filter as shown below, with low frequency cut-off at W = 100 rad/sec and high frequency cut-off at WH=10 krad /sec. (4 pts) a) Determine the center frequency wo and the bandwidth B (10 pts) b) Choose L-100 mH and calculate the values of R and C (6 pts) c) Find the magnitude of H(jw)= Vo / V, and evaluate it at www с...
Homework #2 Problem 14.38 PSpice Multisim Part A Consider the bandreject filter shown in (Figure 1). Suppose that R-4 k2,L-3.5 mH, C-62.5 nF Calculate the center frequency wo. Express your answer using three significant figures vec krad/s Figure 1 of 1 Submit Request Answen Part B Calculate the center frequency f, in kilohertz. Express your answer using three significant figures vec kHz Problem 14.38 PSpice Multisim Part C Consider the bandreject filter shown in (Figure 1). Suppose that R-4 k2,L-3.5...
5) Consider the following second-order bandpass filter. As input voltage, apply V(t) 100Ω, C-4.7 μF. and L-10mH. sin(wt).R in Vout Fig 9: Second-order band-pass filter a) Determine the frequency response function H(ju) Ve-ju) / Vm(ju) and sketch the magnitude and phase characteristics versus w by calaulation. Calculate the theoretical cutoff frequency of the filter Using PSpice AC analysis, plot magnitude lHju)l and phase ф characteristics of the filter, between 1 Hz-100 KHz b) c)
5) Consider the following second-order bandpass...
C V. Figure 2 A band-pass filter circuit This is the transfer function of a band-pass filter having R = R2 //R Center frequency, a[ 1/R' R C12 radians Bandwidth B2(R, C) radians Maximum Gain Ag- R/2R Band-Pass Filter Design Design a band-pass filter to obtain f-160 Hz, B-16 Hz and o- 10. Supply voltages of +20 and -20 Volts are available. Laboratory Measurements and Results . By applying sinusoidal voltage at the input and by varying its frequency, obtain...
200 HZ. 6.25) Design a cascading LC low-pass filter with maxi- mally flat magnitude response. Use a passband of 0 to 5 kHz with 5 kHz cutoff frequency and filter to attenuate all frequencies at and above 10 kHz by at least 30 dB. Use R R1 = 50 2
200 HZ. 6.25) Design a cascading LC low-pass filter with maxi- mally flat magnitude response. Use a passband of 0 to 5 kHz with 5 kHz cutoff frequency and filter...
1. Design the following series RLC filter (find values of R and L) with a quality factor of 5 and a center frequency of 20 krad / s. For the filter that you designed, find the bandwidth and the values of two cutoff frequencies 0.05 HF L
Most questions answered within 3 hours.
-
91. If the half – life of a sample of radioactive
material is 60 days, what...
asked 20 seconds from now -
White light (380nm-750nm) strikes a diffraction grating (420
lines/mm) at normal incidence. What is the highest-order...
asked 9 minutes ago -
1) Explain what is meant by a good being "excludable."?
2) Explain what is meant by...
asked 8 minutes ago -
I need help with this question:
Describe in detail at least two factors that stimulated American...
asked 15 minutes ago -
Calculate the Boyle temperature for helium assuming it follows
the Berthelot equation of state.
asked 16 minutes ago -
Summarize Strategic Corporate Social Responsibility, 4th edition
2017 book, chapter one and two.
asked 16 minutes ago -
1. If the standard deviations for return on stock A and stock B
are 28% and...
asked 31 minutes ago -
Please use python to explain.
Assume that the variables x and
y refer to strings. Write...
asked 38 minutes ago -
This table shows the US domestic demand and supply schedules
for oranges. Suppose the world price...
asked 37 minutes ago -
Please help me create a CLASS DIAGRAM for this code:
import pygame
from pygame.sprite import Sprite...
asked 39 minutes ago -
The Merriweather Printing Company is trying to decide on the
merits of constructing a new publishing...
asked 58 minutes ago -
29) Insulin is a water-soluble hormone transported in the blood.
Which describes a likely way in...
asked 1 hour ago