Problem 2 a) Using 5 nF capacitors, design an active broad- band first-order bandreject filter with a lower cutoff frequency of 1000 Hz, an upper cut-off frequency of 5000 Hz, and a pass band gain of 10dB. b) Draw the schematic diagram of the filter. c) Write the transfer function to find H(jωo), where ωo is the center frequency of the filter. d) What is the gain (in decibels) of the filer at the center frequency? e) Using Matlab make a Bode magnitude of the filter
Problem 2 a) Using 5 nF capacitors, design an active broad- band first-order bandreject filter with...
Part B Using C = 26 nF capacitors, design an active broadband first-order bandreject filter with a lower cutoff frequency of 400 Hz, an upper cutoff frequency of 4000 Hz, and a passband gain of 0 dB. Determine value of resistance in the high-pass filter RH. Express your answer to three significant figures and include the appropriate units. RH = Value Units Submit Request Answer Part C Determine value of resistance in the low-pass filter RL Express your answer to...
Problem 4. (6 marks) You are required to design a third-order Butterworth bandpass filter using ideal operational (6) Passband gain of 12 dB. (i) Lower cutoff frequency, f 6000 Hz. (ii) Upper cutoff frequency, u 12000 Hz. You are constrained to using 1 k? resistors in the lowpass filter and 10 nF capacitors in the highpass filter. Sketch the overall schematic design of your filter with all component values clearly labelled. You must show all of your work in obtaining...
Create a 4th-order lowpass active Chebyshev filter with a 3-dB ripple in the pass band with a corner frequency of 250 Hz using the Sallen-Key topology. Draw the final circuit and all component values. Create a Bode plot for the response at each stage and the overall response using MATLAB
3. For the active filter circuit below, complete the following: a) Find the magnitude of the transfer function | H | starting from the nodal equations. b) Find the phase shift of the transfer function (W) c) Find the cutoff frequency fc in Hz d) Is this a high pass or low pass filter? e) Find the passband gain of the filter 62 k2 ANA EVA 22 nF 3.3k f) Given the following input signal: vi(t) = 1.0 sin(2nft +...
Explain your process please 1. Design 6th order Butterworth band-pass filter with cut-off frequency is 4KHz and 7KHz and pass- band gain is 20dB Draw the circuit, write the transfer function of the filter, and sketch a frequency spectrum of the filter and show the cutoff frequencies on the spectrum Solution:
Design an active band-pass filter such that the center frequency is Fo-2.5 kHz, bandwidth is BW 400 Hz and gain is K-3 for Figure 10.5. Find the values for the capacitors, and resistors. Compute the theoretical values of Vout and |Av Vout / V l and record the results in Table 10.5-A. VEE -15V C1 R3 C2 R1 R2 Vout +VCC +15V Figure 10.5
Homework #2 Problem 14.38 PSpice Multisim Part A Consider the bandreject filter shown in (Figure 1). Suppose that R-4 k2,L-3.5 mH, C-62.5 nF Calculate the center frequency wo. Express your answer using three significant figures vec krad/s Figure 1 of 1 Submit Request Answen Part B Calculate the center frequency f, in kilohertz. Express your answer using three significant figures vec kHz Problem 14.38 PSpice Multisim Part C Consider the bandreject filter shown in (Figure 1). Suppose that R-4 k2,L-3.5...
DESIGN PROBLEM MULTISIN 14.20 Use a 5 nF capacitor to design a series RLC band- pass filter, as shown at the top of Fig. 14.27. The cen- PSPICE ter frequency of the filter is 8 kHz, and the quality factor is 2. a) Specify the values of R and L. b) What is the lower cutoff frequency in kilohertz? c) What is the upper cutoff frequency in kilohertz? d) What is the bandwidth of the filter in kilohertz? p rin...
Using C 210 nF capacitor and other required capacitors, resistors, and ideal op amps, design a low-pass unity-gain Butterworth filter with a cutoff frequency of 40 kHz and is down at least-55 dB at 200 kHz.
Design a second-order high pass active filter with a cutoff frequency of 1Hz and a passband gain of 10. Show all calculations and provide a schematic of your design.