26 please 26, A fluid (specific weight of .0324 lb/n?) flows at an constant flow rate...
2. What hp must be pump deliver to a fluid having a specific weight of 70.0lb/ft if energy losses of 4.5tb-ft/lb occur between points 1 and 2? The pump delivers 60 gal/min of fluic P2 50.0 psig 2-in Schedule 40 steel pipe 25n Flow Pump -2.30psig -in Schedule 40 steel pipe 2. What hp must be pump deliver to a fluid having a specific weight of 70.0lb/ft if energy losses of 4.5tb-ft/lb occur between points 1 and 2? The pump...
34. A coal slurry is found to behave as a power law fluid, with a flow index of 0.3, a specific gravity of 1.5, and an apparent viscosity of 70 cP at a shear rate of 100/s. What volumetric flowrate of this fluid would be required to reach turbulent flow in a 1/2 in. ID smooth pipe, which is 15 ft long? What is the pressure drop in the pipe (in psi) under these conditions? Please show all work, thank...
5. Oil Flow in a Pipe Oil (S 0.80;0.01 lb s ft-2) flows downward in the pipe shown in Figure 3. The pipe diameter is 0.10 ft and has a slope of 30°. The mean fluid velocity is 3 ft s1. What is the pressure gradient, de, along the length of the pipe? 30° Figure 3: Schematic of oil flow in a pipe. Answer(s):-71 lb ft-2 ft-1
The tank contains a fluid with a specific weight of 80.7 lb/ft3 . Determine (a) magnitude of the resultant force exerted by the fluid on the bottom of the tank; (b) magnitude of the resultant force exerted by the fluid on side ABCD; (c) location of the center of pressure on side ABCD (vertical distance below liquid surface); (d) magnitude of the resultant force exerted by the fluid on side AEFD; (e) location of the center of pressure on side...
A venturi meter is used to measure the flow speed of a fluid in a pipe. The meter is connected between two sections of the pipe (the figure); the cross-sectional area A of the entrance and exit of the meter matches the pipe's cross-sectional area. Between the entrance and exit, the fluid flows from the pipe with speed V and then through a narrow ''throat'' of cross-sectional area a with speed v. A manometer connects the wider portion of the...
A Venturi tube may be used as a fluid flow meter. If the fluid flow rate in m3/s is 1.6 * 10-3 and the radius R1 = 2.4 *10-2 m of the inlet tube is 2.9 times the radius R2 of the outlet tube, and the fluid is water (ρ = 1000 kg/m3), find the pressure difference P1 - P2 in units of kPa. Enter a number with one digit behind the decimal point.
glavily UI 0.00! (3.)A 20 in3 sample of oil is compressed in a 2.5 in diameter cylinder until the force applied increased from 1000 lb to 2000 lb. If the bulk modulus equals 300,000 psi, find the change in volume of the oil. 4. For the pipe shown below, calculate: a. The flow rate at point 2 b. The velocity of the fluid at point 1 and point 2 c. The pressure of the fluid at point 2 A2 =...
A fluid of density 1300 kg/m3 flows out through a 3 meter diameter pipe without friction at a rate of 1500 L/s. Find the velocity of the fluid as it flows out of the 3 meter diameter pipe. Note that the 'speed' sensor does not give enough significant figures... use the sensor, to prove your calculations (and not the opposite!) Submit Answer Tries 0/99 Calculate the velocity of the fluid if the pipe constricts to a diameter of 1 meter....
Fluid mechanics! Please answer and explain (w/ details). Will rate! 3) Consider flow through an industrial water pipe. A technician needs to measure the pressure drop along the pipe from P2 to Pi (ie. find what P2- Pi is). Instead of using Castor Oil only, the technician accidently fills the manometer with Decane. Use the manometer shown below to calculate the pressure difference between the two locations along the pipe. Express your answer symbolically using the given parameters as well...
pls write down clearly thanks -2 SKMM2313 QUESTION 1 (a) A compressible fluid flows through a compressor that increases the density from 1 kg/m2 to 5 kg/m. The cross-sectional area of the inlet pipe is 3 m2 and that of the discharge pipe is 1 m2. Determine the relation between the discharge velocity V2 and the inlet velocity Vi (2 marks) In Figure Q1, determine the rate of change of h(t) if the fluid is water. (b) Take V.-10 m/s...