explain the steps of a procedure you would use to separate and recover
a) mixture of sodium chloride and sodium iodide
b) mixture of sand and sodium chloride
explain the steps of a procedure you would use to separate and recover a) mixture of...
Given a solid mixture of the following molecules determine a separate scheme that can be used to separate the mixture using acid base extraction. - 2-hydroxybenzoic acid - 4-chloroanaline - trans-stillbene The following solvents and reagents will be available for use during the experiment 1. 5% sodium bicarbonate 2. 10% sodium hydroxide 3. Saturated sodium chloride 4. 5% hydrochloric acid 5. 6 M hydrochloric acid 6. Diethyl ether 7. Anhydrous sodium or magnesium sulfate *Can you include a experimental procedure...
Suppose you were given a mixture of n-octane, sodium iodide and water to separate. Using the information gathered for these and similar compounds in this experiment, and using what you know about the properties of these materials from other contexts, outline a procedure that could be used to do a quantitative separation of these three materials. Your procedure should be specific enough, that if followed, someone could determine the amount (mass) of each of the three materials present in the...
17. Draw a flow sheet to show how you would separate a mixture of benzoic acid, 2-naphthol, aniline, and naphthalene. (indicate the solvent, location and composition of each layer). Draw all balanced equations. (6') Reagents available: 3M hydrochloric acid solution, 3M sodium hydroxide solution, 3M sodium bicarbonate solution, saturated sodium chloride solution Solvent available: water, dichloromethane, ethanol, and diethyl ether. 17. Draw a flow sheet to show how you would separate a mixture of benzoic acid, 2-naphthol, aniline, and naphthalene....
Which distillation setup would you use to separate a mixture of toluene (boiling point = 110.6 C) and hexane (boiling point = 68 C)? Explain your choice. Which distillation setup would you use to separate a mixture of benzene (boiling point = 80.1 C) and pentane (boiling point = 36.1 C) Explain your choice.
In the procedure you were told to: separate the solid silicon dioxide by filtering the mixture. Provide an alternative method for this separation and explain why you used filtration instead.
Explain how you would separate a picture containing benzophenone, benzoic acid, p-ethylphenol, and p-toluidine? Use a flow chart that clearly shoes the procedure. Begin by dissolving the mixture in diethyl ether.
1.describe how you would separate a mixture of acetanilide and sand 2.water is a convenient solvent for recrsytallizing what type of compound. 3. why is fluted filter paper usually used when doing the hot filtration during a recrystallization. 4.describe how seed crystal are used in recrystallization. 5.explain the adage " like dissolve lik
Question 2,3,4 please. ESTIONS: 1. Many students do not recover 100% of the original mixture. Describe at least two possible problems that could cause less than 100% recovery of the mixture. 2. A student received a mixture that actually contained 50.0% salt and 50.0% sand. At the end of the experiment, this student calculated that his sample was composed of 45.2% salt and 54.8% sand. What might he have done (or not done correctly) during the experiment to cause this...
Organic Chemistry Nitration lab. 1. Aromatic nitration requires the use of the HNO3 / H2SO4 mixture. Why not use HNO3 alone? 2. Why should the cold nitration reaction be maintained at all times? 3. What difference should be observed between the 1 H NMR spectrum of the nitrated reagent and the product obtained? Explain 4. If the yield percentages for acetanilide nitration products were: 35% o-nitroacetanilide and 65% p-nitroacetanilide, explain how you would perform the procedure to separate and recover...
Post-lab Filtration experiment questions. 1. If your goal is to separate oil from sand, estimate how much of oil and how much of the sand do you lose during the vacuum filtration experiment. 2. How would you modify the experiment procedure, if I would give you a mixture on unknown amount of oil and sand and would ask to calculate the weight percentage of sand in the mixture?