Calculate IB , lc, le , VCB, Vce and a for the transistor in Figure 2....
Vcc 10 V #2. Calculate the values of VBE, VCE, IB, Ic, and IE assuming B = 150 for the Transistor Biasing Circuit in Figure 5 - 5. Simulate the circuit in Figure 5 - 5. Include the procedure and results of calculation / simulation in related section. 370k SR2 2370K BROD 2N3904 ŽR3 330 Figure 5 -5: Transistor Biasing
1. For the npn transistor shown in Fig. 1, assue a 98/99, V)0.7V and VCE(sal) 0.2V. Plot Voul, lc, IE ald Ic/IB as a function of IB for 0 < 1B < 150??. 10V 1k Figure 1
(13 points) For the transistor in the circuit shown below, VBE(on) = 0.7 V, Vce(sat) = 0.2 V, and B = 100. Determine the value of the collector current. +5 V R=1.2 ko R =33 k2 -5 V
D. For the transistor circuit shown in Figure 7, assuming that the transistor is in the forward active mode, and B = 100 and VBE = 0.7V, calculate Base current 1B Collector current Ic (iii) Emitter current le (iv) Collector to emitter voltage Vce and (v) Voltage across the 2009 resistor v 3 80022 10 kV W VCE VBE مت + + 1 2001} 1 1
7. Determine the quiescent levels of Ic and Vce for the network of Figure 25. 10 V 4.7 k92 250 k22 16 10 uF B = 90 OH 10 uF 1.2 ΚΩ Figure 25 8. A stage is a transistor and the passive components connected to it. Figure 26 shows a three-stage circuit using two-supply emitter bias. Vec +15 V RCI 10 ΚΩ Ro 10 ΚΩ Rc 10 k 2 Yout R1 RB3 w- RER 33 k22 33 k2 RE1...
1. For the transistor circuit shown in figure 1, what is: a. Vce when VIN = OV? b. What minimum value of IB is required to saturate the transistor if Boc is 200? c. Calculate the maximum value of Rs when Vin = 5V. VCC 10V RC 1.0 K RB Q1 VIN=0V 15C02MH-TLE GND Figure
ASAP! Question 1 [Soalan 1] (a) Describe the condition when a npn BJT transistor operates in saturation condition and what are the terminal currents and voltages conditions during saturation. [Terangkan keadaan bila satu transistor BJT npn beroperasi dalam keadaan tepu dan apakah keadaan arus dan voltan terminal semasa tepu. ] (20 Marks/Markah) (b) Consider the BJT transistor circuit in Figure 1. If Bpc = 100 and VBE = 0.65V, calculate: [Pertimbangkan litar transistor BJT dalam Rajah 1. Jika Bpc =...
DC Biasing For the circuit below, assume 150, VBE(ON) -0.7V and Vce(SAT)- 0.2V Voc 10 VO Rc 3.3K ib Rb 330K Write an equation for ib in terms of Vin (Hint: use KVL from VBB to ground) Write the general equation for ic in terms of ib and P Write an equation for Vce in terms of ic CE- Fill the table Operational Region 0 V 3 V 5 V 7 V
1) Calculate the value of the base current IB. (in μA) 2) Calculate the value of the base collector current IC. (In mA) 3) Calculate the value of the collector-emitter voltage VCE. (In V) Required information In the circuit below: RB = 820 kN, Vcc = 12 V, RC = 3 kN2, and Bdc = 100. Note: The transistor is silicon. Vcc w Rc Re Bdc
2. (20 points) In the circuit shown below the silicon transistor has B=70. (a) Determine Ib, Ic and Vce (the operating point). YOUR ANSWERS: 18 = Ic = VCE = 5.6ko 100k2 3 5.6k2 - 12 V Circuit for problem 2.