can you calculate and explain why? thanks
can you calculate and explain why? thanks A single-phase thyristor rectifier as 50 Hz source. The...
i want the answer with detales
Single-Phase Controlled Rectifier Exercise Derive the expressions of the average load voltage and current in single-phase half-wave controlled rectifiers and resistive load. Draw the waveforms of supply voltage. output voltage, output current, thyristor voltage and thyristor current Exercise In a single-phase half-wave controlled rectifier and resistive kad, it is desired to get an average load voltage of 80 V. Determine the firing angle if the ac supply voltage is 230 V. If the load...
A 3-j semi-controlled bridge rectifier is fed from a delta-star transformer 66 kVA, 60 Hz, 13800 V/? (the secondary voltage is unknown). The load of the rectifier is highly inductive. The following measurements at a specified firing angle have been recorded: Ith RMS 70.71 A I line RMS (transformer secondary) 76.40 A Draw the complete circuit diagram and calculate; i. Load current Io. ii. Firing angle α. iii. Transformer secondary line voltage (RMS). iiii. Average output voltage (at the calculated...
A 3-j semi-controlled bridge rectifier is fed from a delta-star transformer 66 kVA, 60 Hz, 13800 V/? (the secondary voltage is unknown). The load of the rectifier is highly inductive. The following measurements at a specified firing angle have been recorded: Ith RMS 70.71 A I line RMS (transformer secondary) 76.40 A Draw the complete circuit diagram and calculate; i. Load current Io. ii. Firing angle α. iii. Transformer secondary line voltage (RMS). iiii. Average output voltage (at the calculated...
A single-phase full bridge thyristor rectifier is supplied from a 200vrm 50HZ AC source, and supplies a series R-L load comprising a 202 resistance and a 36.8mH inductance 2.a. Sketch the circuit diagram for this rectifier Q2. [4 marks] [Refer to lecture notes] 2.b. Determine the maximum possible average DC voltage that can be achieved across the load resistor [4 marks] [VDC (avg) = 180V] 2.c. Determine the SCR firing angle at which the rectified output curent will just be...
Q4: A thyristor controlled single phase rectifier as shown below. Given that input voltage Vs is 60Hz and 150V amplitude, a) calculate the phase angle needed to produce an output voltage of 20V. b) Sketch the waveforms of the output voltage with clear indication of the firing angle. c) what is the voltage rating needed for T1? ind * Eetro I
A single phase half-wave SCR rectifier is used to reduce the
average voltage across a nonlinear resistive load where the
resistive value is represented by
R = 0. 2 V^2(aver) + 5 Ω
Calculate the load average current when the source voltage is
110 V RMS and the triggering angle is 90 degrees
A single phase half-wave SCR rectifier is used to reduce the average voltage across a nonlinear resistive load where the resistive value is represented by aver Calculate...
(i) (ii) Draw the structural diagram of a Gate Turn-Off (GTO) thyristor. [7%] Explain the operation of GTO and clearly state the voltage and frequency range for its application [15%] State four advantages of GTOs when compared to conventional thyristors. (iii) [8%] (b) Consider the single-phase full bridge rectifier shown below where R=6 12, L = 6 mH, E = 60 V and the ac source voltage is 230 V, 50 Hz. * * 13 பண்பு 14* (i) For continuous...
b. Consider the single-phase fully controlled of thyristor bridge rectifier supplies a load consists of R-L load and Vee in series as shown in Figure Q2 (b). The parameters for this circuit are as follows: supply voltage is 120 Vrms at 60 Hz, DC voltage, Voe equal to 10 v. i. Sketch the waveforms for output voltage, thyristor current, diode current and output current (CO2: PO2 - 5 marks) Calculate the output voltage, Va at a = Tt/2. (CO2: PO2...
Controlled three-phase rectifiers Figure 4-20a shows a controlled six-pulse three-phase rectifier. The delay angle a is referenced from where the SCR would begin to conduct if it were a diode. Sketch the output voltage of the controlled rectifier for a delay angle of 60°
2. Figure 2 shows a 6-pulse thyristor rectifier feeding a DC static load an operating at steady-state. The ac input power supply is a symmetric set of three-phase voltages forming a direct sequence, having rms line-to-line voltage of Vuns equal to 415 V and angular frequency ω equal to 100π rad/s. The load is sufficiently inductive to smooth out the load current i(t), i.e. i 1, where I is a constant. a. Derive the mathematical expression of the average DC...