*Please answer all with correct answer and show clean and clear step! Thank you!*
*Please answer all with correct answer and show clean and clear step! Thank you!* 0 Figure...
done on pspice thank you Part IV: Diode Rectifiers Procedure: 1. Build the circuit model for full-wave diode rectifier in PSpice as shown in Fig. 4. The value of the load resistor is 10 k22. The input AC voltage source (VSIN in PSpice) is configured at 100 Hz and 20 V (peak-to- peak) in sinusoidal waveform. O 10K V.(t) V(A) A Figure 4. Circuit configuration for full-wave diode rectifier 2. Run the simulation and save the input and output voltage...
HI, PLEASE ANSWER ALL PARTS AND PLEASE SHOW ALL WORKINGS STEP BY STEP. THANK YOU. Question 1: a) Show from first principles that the Laplace transform of the function f(n)=1, 120 is f(s) = Make a note of any conditions imposed on the transform variable "s" to ensure the transform exists. (8 Marks) b) Find, using the appropriate theorem, the Laplace transform of a function f(t); b) f(t) = t.sin(56) OR ii) f(t) = 5 sin 2(t - 3). H(t...
This is control system question. please answer all and show a clear step. Thank you! Question 3 Given the translational system shown in Figure 2, an input force, f(t) is applied to the mass, M, causing the dashpot which has a viscosity B and the spring, a stiffness coefficient of k, to compress with output displacement X(t). Input force, f(t) M O F Fixed point Displacement, X(t) Figure 2: A translational system (a) Derive the system's equation in terms of...
1) Please answer full question (a-c) showing work. Ensure answer is correct for thumbs up. a) If the FFT of an 1000-Hz square wave was measured to be approximately -1.8 dBV. What is the corresponding rms value? b) The third harmonic of the square wave was measured to be approximately -11.34 dBV. What is the corresponding rms value? c) The output voltage across an 8-Ω speaker was measured as 1-kHz sinusoidal signal with peak amplitude 7 Vp. Calculate the value...
PLEASE, I WANT THE ANSWER WITH GOOD HANDWRITING PLEASE, AND CLEAN AND CLEAR. THANK YOU 3. An L 5x 3 %x % angle is used as a compression member of a bridge. If L-10 feet, determine the allowable stress for Fy -36 ksi. What boundary conditions do you pick for the two ends? Why? What is the allowable axial load for extension? Explain.
Please show clear step by step solution. 3. (8 marks) The current iſt) in an LRC-series circuit can be determined from the integral equation 10 L + Ri(t) + Pille) + d. Juobdr = Ele). 1 i(t)dt = E(t). Determine i(t) when L = 0.005 h, R=11, C = 0.02 f, and E(t) = 100[t – (t-1)U(t - 1)].
clear handwrite and step by step solution please thank you in advance Q2. For the single-phase voltage controller of Fig. 2, the source is 120 Vrms at 60 Hz, andthe load is a series Rしcombination with R-20 Ω and L-50 mH. The delay angle α is 90°. Determine (a) an expression for load current for the first half-period, b) the rms loadcurrent, (c) the rms SCR current, (d) the average SCR current, (e) the power delivered tothe load, and (f)...
Please answer full question thoroughly (A, B & C) showing detailed work. Double check answer and work to ensure it is correct for thumbs up. 1) Assume the voltage source delivers a 50-Hz sinusoidal signal. Using the oscilloscope, the voltage (t) was as shown in the figure. PUR(t) Vi sin(27 fot) v it T UD T-lt V2X SUR Exam -30 -20 -10 0 10 20 30 40 50 60 t (ms) (a) Explain the shape of the voltage waveform...
Please show step for step and, all equations used. Thank you. 1) For the power supply circuit: 120v Dc. 6Oh time values on your sketch E. hat is the DC load Current? 7 C. What is the average current in each diode? I = D. what is th peak current in each uld be reqLlired to redLICe the E. What minimLm va l Lle.Pf capac i tor 120v 7 1 For the power suipply circuit: ツー time values on Your...
PLEASE ANSWER ALL PARTS OF THE QUESTION A single-phase full-wave rectifier in the following figure has a ripple-free average load current of Ia (Highly-Inductive-Load). Assume a transformer turns ratio of unity. (1) Draw the waveform for current ipi, io2 and ip through D1, D2, and at the primary side of transformer, respectively; (2) Express the input primary current ip() in Fourier series (3) Determine the input PF of the rectifier and HF (or THD) of the input primary current ip(t)....