The load appiled is transmitted directly to the weld joint.
So the tensile force acts on the weld joint and the weld joint is approximated as a triangle with base and height as leg size.It is approximated to fail about a plane which has least cross sectional area.
Shear failure is most likely to occur on the least cross sectional area plane,so we consider shear stress in that plane.
Hope it helps.
Thank you.
2. A round tube of diameter 2 inches is welded to a wall and subjected to...
2. A round tube of diameter 2 inches is welded to a wall and subjected to a tensile force of 5000 lbs as shown. The weld rod is E60. The weld leg is 0.25 inches. What is the factor of safety guarding against weld metal yielding as a result of this force? a) 1.62 b) 2.48 c) 3.38 d) 4.13 e) None of these lbs F 5000 2. A round tube of diameter 2 inches is welded to a wall...
3. A square tube of side 2 inches is welded to a wall where only the top and bottom edges are welded. The weld leg is 0.25 inches and the weld electrode is E60. The figure shows that the tube is subjected to a bending force of 500 lbs acting at a distance of 12 inches. Ignoring direct shear stresses, what is the factor of safety guarding against yielding of the weld metal? a) 1.6 e) None of these d)...
4. A round tube of diameter 2 inches is under pure torsion of 8000 in-lb as shown in The tube is welded to the post all-around using a E70 electrode. If the weld leg is 0.25 inches, what is the factor of safety guarding against yielding? d) 3.83 b) 1.64 c) 2.91 e) None of these a).82 ,n 4. A round tube of diameter 2 inches is under pure torsion of 8000 in-lb as shown in The tube is welded...
I need the whole solution for this question! Thanks 2.6 Calculate the safe working pressure for a 2 m diameter spherical container, with wall thickness 15 mm, if the ultimate tensile strength of its material is 420 MPa, the factor of safety is 6 and the efficiency of welded joints is 90%. 2.6 Calculate the safe working pressure for a 2 m diameter spherical container, with wall thickness 15 mm, if the ultimate tensile strength of its material is 420...
2. (2 marks) Consider a pre-loaded threaded bolted joint subjected to static load P as shown in the figure below. This figure shows one of the bolts of a threaded joint that is part of a group of uniformly loaded bolts. The bolt is a SA Grade 4 bolt having a major diameter d0.375 in and the pitch p - 0.0625 in. The two steel members, marked 2 and 3 in the figure below, have the thickness of 0.5 in...
please answer both the questions Question 2 A titanium tube 200mm diameter and 5mm wall thickness is subjected to an internal pressure of 13.5MPa. The tube contains a longitudinal crack along its full length. Assuming that the tube can be approximated by a single edge notched plate subjected to a tensile stress equal to the hoop stress in the tube determine the crack length to cause failure. You may assume that the material fracture toughness is 55 MPavm. Please provide...
JUMBO CONCRETE WALL SUPPORT PIPE TINY PLATFORM PERC PERCH Here is what is known: Jumbo has a weight of 15,000 lbf Tiny has a weight of 5000 lbf. The support tube is fabricated from AISI L-6 tool steel, quenched and tempered at 600 degrees F. (Note: This would be an insanely expensive choice for this tube, AND it would be really hard to weld but the zoo had a big piece of pipe made out of tool steel just laying...
An alumninum (E = 68.9 GPa) cylindrical tube has an outer diameter of 200 mm, a wall thickness of 7.5 mm, and an internal pressure of 5 MPa. It is subjected to a force with the axial and transverse components shown acting at the centroid of the free end of the tube 1. Verify that the tube meets the thin-wall criterion 2. Draw the left half of the tube, and show the equivalent force-couple system acting at the centroid of...
Please take P=1501.6 N Remaining time: 145:05 1 2 3 4 5 6 Question 6 Force of P = 1500 + S N is applied to the rigid arm ABC as shown in the figure. Determine the average shear stress developed in the 6-mm diameter pin B that is subjected to double shear. What is the minimum required diameter d of steel rod CD to the nearest mm. Apply a factor of safety F.S. = 1.5 against yielding. 0,= 300...
Properties for all problems Sut = 80 ksi, 5= 60 ksi, Sf = 40 ksi, q=0.85 (notch sensitivity), steel E = 30e6 psi Remember we use Modified-Goodman for all calculations Problem 1 A 1-inch diameter rod that is 8 inches long has a bearing at one end and another bearing at 6 inches (treat bearings as simple supports). A vertical load is applied at the end of the overhanging rod and a torque is transmitted through the length of the...