Homework Answers
Add Answer to:
A motor delivers 500 hp to the shaft, which is tubular and has an outer diameter...
A motor delivers 500 hp to the shaft, which is tubular and has anPart A outer...
A motor delivers 500 hp to the shaft, which is tubular and has anPart A outer diameter of 2 in. The shaft is rotating at 236 rad/s hp 550 ft.Ib/s.(Figure 1) Determine its largest inner diameter of the shaft i the alowable sheor stress for the materialis a Express your answer to three significant figures and include the appropriate units 25 ksi 因 ? d1.53 in Submt Incorrect: Try Again; 4 attempts remaining Provide Feedhack Figure 1 of 6 in....
Alt h. 10- The motor delivers 40 hp to the 304 stainless steel shaft while it...
Alt h. 10- The motor delivers 40 hp to the 304 stainless steel shaft while it rotates at 20 Hz. The shaft is supported on smooth bearings at A and B, which allow free rotation of the shaft. The gears C and D fixed to the shaft remove 25 hp and 15 hp, respectively. Determine the diameter of the shaft to the nearest 1/8 in. if the allowable shear stress is 8 ksi and the allowable angle of twist of...
Question 2: The shaft ABC shown in the figure is driven by a motor that delivers...
Question 2: The shaft ABC shown in the figure is driven by a motor that delivers 300kW at a rotational speed of 32 rev/sec. The gears at B and C take out 120k W and 180kW respectively. diameter of the shaft if the allowable shear stress is 50MPa, the allowable angle of twist between points A and C is 4° and G- 75GPa. of the two parts of the shaft are Li = 1.5m and L,-0.9m. Determine the required Motor...
1. The motor in the figure below delivers 150 hp while turning at a constant rate of 3600 rpm at ...
1. The motor in the figure below delivers 150 hp while turning at a constant rate of 3600 rpm at A. Using the belt and pulley system this loading is delivered to the steel blower shaft BC a. Determine the torque output of the motor. b. What is the force in the belt. c. What is the torque delivered to the blower shaft. d. What is the angular frequency of the blower shaft and power delivered to the blower. How...
A steel tube having an outer diameter of 2.5 in is used to transmit 12.5 hp...
A steel tube having an outer diameter of 2.5 in is used to transmit 12.5 hp when turning 30rev/min. Determine the inner diameter of the tube to the nearest 1/8 in. if the allowable shear stress is 10ksi. 251
Problem Two (30 pts): Design a solid circular shaft for a motor. The motor must supply...
Problem Two (30 pts): Design a solid circular shaft for a motor. The motor must supply 15 hp, and 100 revolutions per minute. Specify the diameter of the shaft to the nearest 1/8 inch. The shear yield stress of the shaft is 60 ksi, and the design should use a factor of safety of 1.5 the shaft will turn at ust su ,-60 ksi F.S.= 1.5 7 P- 15 hp f= 100 rpm Motor
A steel tube having an outer diameter of 2.5 in. is used to transmit 9 hp...
A steel tube having an outer diameter of 2.5 in. is used to transmit 9 hp when turning at 27 rev/min. 1 hp = 550 ft?lb/s. Determine the inner diameter d of the tube if the allowable shear stress is ?allow = 10ksi . it is a hollow tube.
A hollow shaft 36 inches long transmits 110 HP at 1300 rpm. The shaft is made...
A hollow shaft 36 inches long transmits 110 HP at 1300 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degrees over the 36 inches length. The inside diameter of the shaft is 0.65 that of the outside diameter of the shaft. Determine: a) the required inside and outside diameter of the shaft based on...
Section 2. Problem 6 (25 pts.) A hollow shaft 36 inches long tranmits 125 HP at...
Section 2. Problem 6 (25 pts.) A hollow shaft 36 inches long tranmits 125 HP at 1100 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degreees over the 36 inche length. The inside diameter of the shaft is 0.6 that of the outside diameter of the shaft. Determine: a) the required inside and outside...
Question 1. (a) A steel tube having inner and outer dimeters of 1.5 in. and 2...
Question 1. (a) A steel tube having inner and outer dimeters of 1.5 in. and 2 in., respectively, is turning at 45 rev/min. If the allowable shear stress (Tallow) of the tube material is 10 ksi, determine the horse power (hp) transmitted by the tube. (20 points) (b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60 mm. The shaft is used to transmit a torque of T = 524 N-m from the engine...
A motor delivers 500 hp to the shaft, which is tubular and has anPart A outer diameter of 2 in. The shaft is rotating at 236 rad/s hp 550 ft.Ib/s.(Figure 1) Determine its largest inner diameter of the shaft i the alowable sheor stress for the materialis a Express your answer to three significant figures and include the appropriate units 25 ksi 因 ? d1.53 in Submt Incorrect: Try Again; 4 attempts remaining Provide Feedhack Figure 1 of 6 in....
Alt h. 10- The motor delivers 40 hp to the 304 stainless steel shaft while it rotates at 20 Hz. The shaft is supported on smooth bearings at A and B, which allow free rotation of the shaft. The gears C and D fixed to the shaft remove 25 hp and 15 hp, respectively. Determine the diameter of the shaft to the nearest 1/8 in. if the allowable shear stress is 8 ksi and the allowable angle of twist of...
Question 2: The shaft ABC shown in the figure is driven by a motor that delivers 300kW at a rotational speed of 32 rev/sec. The gears at B and C take out 120k W and 180kW respectively. diameter of the shaft if the allowable shear stress is 50MPa, the allowable angle of twist between points A and C is 4° and G- 75GPa. of the two parts of the shaft are Li = 1.5m and L,-0.9m. Determine the required Motor...
1. The motor in the figure below delivers 150 hp while turning at a constant rate of 3600 rpm at A. Using the belt and pulley system this loading is delivered to the steel blower shaft BC a. Determine the torque output of the motor. b. What is the force in the belt. c. What is the torque delivered to the blower shaft. d. What is the angular frequency of the blower shaft and power delivered to the blower. How...
A steel tube having an outer diameter of 2.5 in is used to transmit 12.5 hp when turning 30rev/min. Determine the inner diameter of the tube to the nearest 1/8 in. if the allowable shear stress is 10ksi. 251
Problem Two (30 pts): Design a solid circular shaft for a motor. The motor must supply 15 hp, and 100 revolutions per minute. Specify the diameter of the shaft to the nearest 1/8 inch. The shear yield stress of the shaft is 60 ksi, and the design should use a factor of safety of 1.5 the shaft will turn at ust su ,-60 ksi F.S.= 1.5 7 P- 15 hp f= 100 rpm Motor
Section 2. Problem 6 (25 pts.) A hollow shaft 36 inches long tranmits 125 HP at 1100 rpm. The shaft is made out of steel with a modulus of rigidity of 11000 ksi. The shaft has an allowable sear stress of 12 ksi and an allowable angle of twist of 2.5 degreees over the 36 inche length. The inside diameter of the shaft is 0.6 that of the outside diameter of the shaft. Determine: a) the required inside and outside...
Question 1. (a) A steel tube having inner and outer dimeters of 1.5 in. and 2 in., respectively, is turning at 45 rev/min. If the allowable shear stress (Tallow) of the tube material is 10 ksi, determine the horse power (hp) transmitted by the tube. (20 points) (b) The A-36 solid steel shaft is 3.5 m long and has a diameter of 60 mm. The shaft is used to transmit a torque of T = 524 N-m from the engine...
Most questions answered within 3 hours.
-
Accent Software faces the following conditions. All of these
support Accent’s use of a market-penetration pricing...
asked 12 minutes ago -
A mathematically inclined friend emails you the following
instructions: "Meet me in the cafeteria the first...
asked 14 minutes ago -
A monopoly sells in two countries . The demand curves in the two
countries are p1...
asked 1 hour ago -
A .15kg rubber ball is bounced off a wall. Before hitting the
wall, the ball moves...
asked 1 hour ago -
A manufacturing company preparing to build a new plant is
considering three potential locations for it....
asked 1 hour ago -
B. If compound Y has approximately the same values of solubility
in toluene as compound X,...
asked 2 hours ago -
Oscar Inc. has inventory in Japan valued at 39,051,000 Yen one
year ago. One year ago...
asked 2 hours ago -
If Canada suffered from "fundamental disequilibrium," and its
government choose not to devalue its currency, a...
asked 2 hours ago -
4. How many input & output Key Value Pairs are passed into,
and emitted out of...
asked 2 hours ago -
Why would your heart not function well if constructed of
skeletal muscle? What is the particular...
asked 2 hours ago -
Please respond to this essay question in full essay form for
Chemistry 1102 Organic and Biochemistry:...
asked 2 hours ago -
Determine the head loss and velocity of flow in a water supply main
of 15.0 cm...
asked 3 hours ago