Please help me with this homework...Given the circuit below, draw the output characteristic curve showing the load line, maximum values, and actual currents and voltage on the circuit your characteristic. Calculate the RB
We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
Given the circuit below, draw the output characteristic curve showing the load line, maximum values and actual currents and voltage on circuit your characteristic. Calculate the RB.
Calculate voltage across the load resistor and draw the output voltage waveform in the following circuit.
Q.6 For the series circuit in Figure given below, Determine Assume R -500n Vin-10V . The center frequency (f) b. The output voltage magnitude at (f) c. The bandwidth (BW )for the filter d. Draw the output response curve showing the maximum voltage, center frequency and the voltage where the BW is measured 150Ω 100μH Q.6 For the series circuit in Figure given below, Determine Assume R -500n Vin-10V . The center frequency (f) b. The output voltage magnitude at...
Consider the following single phase circuit (one-line diagram): a) Calculate and draw the equivalent per unit circuit b) What is the voltage at the load (actual)? :208 208: 1 Load Ziad 0.082 130.082 Ω c) Calculate the apparent power, active power, reactive power (actual values) at the load d) What is the power factor at the load? Consider the following single phase circuit (one-line diagram): a) Calculate and draw the equivalent per unit circuit b) What is the voltage at...
2) Draw the load line on the I-V curve given below for the following circuit. R1 R4 VD 2k 1k D1 R2 2k R3 2k Vin 8V 1N4148 I(D1) 4.4mA 0.0mA 3.2V 3.6V 4.0V 0.4V 0.8V 1.2V 1.6V 2.0V 2.4V 2.8V 0.0V
For your choice of input voltage, load resistor and the value of the ripple voltage (as percent of Vdc) design a circuit for the half-wave rectifier. Assuming the value of Van for the diode, calculate theoretically all parameters of the rectifier: Vp, Vdc, Idc, C, Isc, PIV and diode conducting interval. Simulate the designed circuit first without the capacitor filter and show on the graphs of the input, output and diode voltages and load and diode currents. Show on the...
Q1. (a) Draw the voltage-current characteristic curve of the GTO, and explain its operating principle. What are the typical ranges of the turn off gain and the switching frequency of the GTO? (b) MAX724 buck converter is shown in Figure Q1. The input voltage is chosen as 25V, and the switching frequency is 100 ?HZ. (i) Calculate the duty cycle, peak-to-peak inductor ripple current, and peak-to-peak output ripple voltage. (ii) Calculate the minimal load current such that the inductor current...
To design a high efficiency d.c., to d.c power converter with the given specifications min 10V max 15V nominal (regulated) 8V Input voltage: Output voltage: Nominal load current: 4A Inductor current ripple: 0.1A max Switching frequency: 30 kHz Output voltage ripple: 20 mV Define a suitable power circuit topology to meet the above specification? Sketch a circuit diagram of the chosen power circuit topology (a) Define the minimum and maximum duty cycles assuming that the control circuit keeps the output...
Need help with this. Circuits need to be done on Multisim. I will give you a good rating if you can help me out. Consider a two-diode AND logical gate circuit. Calculate and build a table showing the values of output voltages for 4 different combinations of input voltages. Simulate the circuit in Multisim for all above values of the input voltages, and observe the actual values of the output voltage. Add the simulation results to the table, compare, analyze,...
Problem: (1) For the single phase AC circuit shown below, calculate voltage phasor across the load showing amplitude and phase angle for a (reference) source voltage of 220 V and 0 degree. Also, attach your MultiSIM simulation showing the voltage amplitude across the load. Compare simulated and calculated values. Load Bus of an Industrial Facility (equivalent of Electrical Motors and power factor correction Cap in parallel). R1 L1 Vload-? 1 3.0ohm 2 10mH 3 4.7mH 4 20ohm R2 +220V, 60...
Question 1 A purely resistive load has a VSWR of 3 in a lossless transmission line. Given that the characteristic impedance is 50 ohm, find all possible values for the load impendence Illustrate your answer using a Smith Chart (5 marks) Question 1 A purely resistive load has a VSWR of 3 in a lossless transmission line. Given that the characteristic impedance is 50 ohm, find all possible values for the load impendence Illustrate your answer using a Smith Chart...