Question

On the Stuve diagram below, at which of the following pressure levels is the relative humidity lowest?171114/1200 72528 BUF LCLP: 988 LIFT: 16 TOTL 29 100 200 300 400 500 S00 700 800 900 1000 -80 -70 -60 -504030 -20 -10 20 30 4

800 mb

460 mb

440 mb

575 mb

0 0
Add a comment Improve this question Transcribed image text
Answer #1

Answer: 460 mb Explanation: The closer lines indicate the highest humidity value. From the given figure, the values 800 mb an

Add a comment
Know the answer?
Add Answer to:
On the Stuve diagram below, at which of the following pressure levels is the relative humidity...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions
  • Problem 10-31 (Algo) Large-scale integrated (LSI) circuit chips are made in one department of an electronics...

    Problem 10-31 (Algo) Large-scale integrated (LSI) circuit chips are made in one department of an electronics firm. These chips are incorporated into analog devices that are then encased in epoxy. The yield is not particularly good for LSI manufacture, so the AQL specified by that department is 20% while the LTPD acceptable by the assembly department is 52%. Assume the company is willing to accept a consumer's risk of 10 percent and a producer's risk of 5 percent. Use Exhibit...

  • The phase diagram for the iron-carbon Fe-C system is shown below. use it to answer the...

    The phase diagram for the iron-carbon Fe-C system is shown below. use it to answer the following questions a) How many different solid allotropes (phases) does pure iron have? b) what is the maximum carbon solubility of carbon in austentite? c) what is the maximum carbon solubility of carbon in ferrite? d)On cooling the following phase reaction occurs at 0.76% C and 727*c y--> alpha + Fe3C. On cooling what phase reaction occurs at .16% C and 1493*c? e)For a...

  • Can somone show me how to do the 1st problem? Need to find the LS and...

    Can somone show me how to do the 1st problem? Need to find the LS and SS for the fit and the LH and SH for the hole. Fits are all SHAFT BASIS METRIC but the shaft and hole diameters can not be used right out of the table. This is because the 3mm shaft tolerance does not match. You will need to lookup the "Fit" from the table, and then use the LS (Largest Shaft) and SS (Smallest Shaft)...

  • In C++ Programming: Using a single for loop, output the even numbers between 2 and 1004...

    In C++ Programming: Using a single for loop, output the even numbers between 2 and 1004 (inclusive) that iterates (loops) exactly 502 times. The outputted numbers be aligned in a table with 10 numbers per row. Each column in the table should be 5 characters wide. Do not nest a loop inside of another loop. Hint: First create and test the code that output the numbers all on one line (the command line will automatically wrap the output to new...

  • The following transactions occurred in June 2018 for Borderline Ltd JuneReceved a cheque for S1 200 from Roar Ltd in...

    The following transactions occurred in June 2018 for Borderline Ltd JuneReceved a cheque for S1 200 from Roar Ltd in full settlement of its account and deposited it in the bank account Sold inventory for $905(before any discounts have been applied) to Jones Ltd on credit (the company was given a trade discount of $80, then the normal credit terms) COGS was $420 Paid rent for June S1 500, chq no. 561 (Assume the rent is GST free) Purchased inventory...

  • Determine the identity of each of the following six unknown hormones using the autopsy data listed...

    Determine the identity of each of the following six unknown hormones using the autopsy data listed for each (Figures 8 through 13) compared to the controls (in Table 1 and Fig. 4). Hormone 1 FIG. 8 Autopsy results from rats treated with hormone 1. Hormone 1 Cintact) Pituitary: 10.1 mg Thyroid: 245 mg Thymus: 250 mg Adrenals: 100 mg Seminal vesicles: 490 mg Prostate: 430 mg Testes: 3000 mg Body weight: 2009 Hormone 1 (castrate) Pituitary 10.1 mg Thyroid: 250...

  • 1. Given the following horizontal curve and spiral data: Total tangent deflection angle (A) = 30°...

    1. Given the following horizontal curve and spiral data: Total tangent deflection angle (A) = 30° Rt. D=50 Design Speed = 50 mph Two lane road in Southern Climate PI Station @ 64+20.00 Find and e from Table 13.8 or 13.9 (see handouts) Compute: R P= Compute the stations of: T.S. = S.C. = C.S. S.T. = Compute the Long Tangent and the Short Tangent PI 4 CPI To AC ST To S.C. C.S. SPI, SPI -Ls 20$ Cc 3...

  • no you dont. let someone else answer it. 1. Given the following horizontal curve and spiral...

    no you dont. let someone else answer it. 1. Given the following horizontal curve and spiral data: Total tangent deflection angle (A) = 30° Rt. D= 5° Design Speed = 50 mph Two lane road in Southern Climate PI Station @ 64+20.00 Find and e from Table 13.8 or 13.9 (see handouts) Compute: = R P= Compute the stations of: T.S. = S.C. C.S. = S.T. = Compute the Long Tangent and the Short Tangent Table 13.9 SPIRAL CURVE LENGTHS...

  • 174 2 combustor , =1500 K Problem 2 (22 pts): Brayton cycle and entropy calculations An...

    174 2 combustor , =1500 K Problem 2 (22 pts): Brayton cycle and entropy calculations An open Brayton cycle is used to generate electricity. Air enters the isentropic compressor at T1 = 300 K and P1 = 100 kPa with a mass flow rate m = 1.5 kg/s. The combustor can be modeled as a constant-pressure heat exchanger, supplying 1540 kW of thermal power to the air from a thermal reservoir (Th = 1750 K). Air enters the isentropic turbine...

  • The Boeing 747 has a cruising altitude of 45,000 feet and cruising speed of 275 m/s....

    The Boeing 747 has a cruising altitude of 45,000 feet and cruising speed of 275 m/s. At this elevation, the temperature and pressure according to the US Standard Atmosphere (air properties as a function of altitude) are 220K and 1.8x104 Pa, respectively. The engines are steady state devices that can be modeled using the 1st Law of Thermodynamics with air (ideal gas) as the working fluid undergoing several processes. a. The inlet area of the engines is 0.5 m2. What...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT